Thương hiệu phân phối chính hãng
Giỏ hàng

Mã lỗi Konica-Minolta bizhub 4750 — Trang 9/27

Code: 3423-121.24

Description: Fuser warm-up trouble
Fuser never reached detection temperature
Causes: • Controller board (CTLB) • Power supply unit (PU)
Remedy: 1 Check the fuser cables JTHERM1 and JEXIT for proper connection to the CTLB. Reseat the cables if any abnormality is found. 2 Check the cable PCN5 for proper connection to power supply. Reseat the cables if any abnormality is found. 3 Check the cables JTHERM1, JEXIT and PCN5 for damage. Replace the fuser unit if any abnormality is found. 4 Check for resistance on the fuser cable. 1. Turn off the printer. 2. Remove the rear door and cover. 3. Disconnect the fuser cable connected to PCN5 of PU. 4. Check for approximate correct resistance on the fuser cable: 220V/43Om, 110V/10U, 100V/8Om

Code: 3423-121.25

Description: Fuser warm-up trouble
After line voltage detection, control did not roll over to steady state control in time.
Causes: • Controller board (CTLB) • Power supply unit (PU)
Remedy: 1 Check the fuser cables JTHERM1 and JEXIT for proper connection to the CTLB. Reseat the cables if any abnormality is found. 2 Check the cable PCN5 for proper connection to power supply. Reseat the cables if any abnormality is found. 3 Check the cables JTHERM1, JEXIT and PCN5 for damage. Replace the fuser unit if any abnormality is found. 4 Check for resistance on the fuser cable. 1. Turn off the printer. 2. Remove the rear door and cover. 3. Disconnect the fuser cable connected to PCN5 of PU. 4. Check for approximate correct resistance on the fuser cable: 220V/43Om, 110V/10U, 100V/8Om

Code: 3423-121.26

Description: Fuser warm-up trouble
Failed to reach temperature during warm up.
Causes: • Controller board (CTLB) • Power supply unit (PU)
Remedy: 1 Check the fuser cables JTHERM1 and JEXIT for proper connection to the CTLB. Reseat the cables if any abnormality is found. 2 Check the cable PCN5 for proper connection to power supply. Reseat the cables if any abnormality is found. 3 Check the cables JTHERM1, JEXIT and PCN5 for damage. Replace the fuser unit if any abnormality is found. 4 Check for resistance on the fuser cable. 1. Turn off the printer. 2. Remove the rear door and cover. 3. Disconnect the fuser cable connected to PCN5 of PU. 4. Check for approximate correct resistance on the fuser cable: 220V/43Om, 110V/10U, 100V/8Om

Code: 3423-121.28

Description: Fuser warm-up trouble
Failed to reach EP warm up temperature in time.
Causes: • Controller board (CTLB) • Power supply unit (PU)
Remedy: 1 Check the fuser cables JTHERM1 and JEXIT for proper connection to the CTLB. Reseat the cables if any abnormality is found. 2 Check the cable PCN5 for proper connection to power supply. Reseat the cables if any abnormality is found. 3 Check the cables JTHERM1, JEXIT and PCN5 for damage. Replace the fuser unit if any abnormality is found. 4 Check for resistance on the fuser cable. 1. Turn off the printer. 2. Remove the rear door and cover. 3. Disconnect the fuser cable connected to PCN5 of PU. 4. Check for approximate correct resistance on the fuser cable: 220V/43Om, 110V/10U, 100V/8Om

Code: 3423-121.29

Description: Fuser warm-up trouble
Fuser failed to reach pre-heat temperature for motor start during warm up.
Causes: • Controller board (CTLB) • Power supply unit (PU)
Remedy: 1 Check the fuser cables JTHERM1 and JEXIT for proper connection to the CTLB. Reseat the cables if any abnormality is found. 2 Check the cable PCN5 for proper connection to power supply. Reseat the cables if any abnormality is found. 3 Check the cables JTHERM1, JEXIT and PCN5 for damage. Replace the fuser unit if any abnormality is found. 4 Check for resistance on the fuser cable. 1. Turn off the printer. 2. Remove the rear door and cover. 3. Disconnect the fuser cable connected to PCN5 of PU. 4. Check for approximate correct resistance on the fuser cable: 220V/43Om, 110V/10U, 100V/8Om

Code: 3423-121.30

Description: Fuser warm-up trouble
Fuser failed to reach printing temperature by the time a page reached the fuser.
Causes: • Controller board (CTLB) • Power supply unit (PU)
Remedy: 1 Check the fuser cables JTHERM1 and JEXIT for proper connection to the CTLB. Reseat the cables if any abnormality is found. 2 Check the cable PCN5 for proper connection to power supply. Reseat the cables if any abnormality is found. 3 Check the cables JTHERM1, JEXIT and PCN5 for damage. Replace the fuser unit if any abnormality is found. 4 Check for resistance on the fuser cable. 1. Turn off the printer. 2. Remove the rear door and cover. 3. Disconnect the fuser cable connected to PCN5 of PU. 4. Check for approximate correct resistance on the fuser cable: 220V/43Om, 110V/10U, 100V/8Om

Code: 3423-121.31

Description: Fuser warm-up trouble
Fuser is too hot. Global overtemp check.
Causes: • Controller board (CTLB) • Power supply unit (PU)
Remedy: 1 Check the fuser cables JTHERM1 and JEXIT for proper connection to the CTLB. Reseat the cables if any abnormality is found. 2 Check the cable PCN5 for proper connection to power supply. Reseat the cables if any abnormality is found. 3 Check the cables JTHERM1, JEXIT and PCN5 for damage. Replace the fuser unit if any abnormality is found. 4 Check for resistance on the fuser cable. 1. Turn off the printer. 2. Remove the rear door and cover. 3. Disconnect the fuser cable connected to PCN5 of PU. 4. Check for approximate correct resistance on the fuser cable: 220V/43Om, 110V/10U, 100V/8Om

Code: 3423-121.32

Description: Fuser warm-up trouble
Open fuser main thermistor.
Causes: • Controller board (CTLB) • Power supply unit (PU)
Remedy: 1 Check the fuser cables JTHERM1 and JEXIT for proper connection to the CTLB. Reseat the cables if any abnormality is found. 2 Check the cable PCN5 for proper connection to power supply. Reseat the cables if any abnormality is found. 3 Check the cables JTHERM1, JEXIT and PCN5 for damage. Replace the fuser unit if any abnormality is found. 4 Check for resistance on the fuser cable. 1. Turn off the printer. 2. Remove the rear door and cover. 3. Disconnect the fuser cable connected to PCN5 of PU. 4. Check for approximate correct resistance on the fuser cable: 220V/43Om, 110V/10U, 100V/8Om
Đăng ký nhận bản tin Đăng ký nhận bản tin Đăng ký nhận bản tin Đăng ký nhận bản tin
Đăng ký nhận bản tin
Nhận ưu đãi sớm nhất khi chương trình diễn ra

Đăng ký nhận bản tin

Việc cho phép sử dụng cookie sẽ giúp cải thiện trải nghiệm của bạn trên trang web này. Chính sách cookie