Thương hiệu phân phối chính hãng
Giỏ hàng

Mã lỗi Konica-Minolta bizhub 502 — Trang 10/25

Code: C225C

Description: K PC drum motor’s turning at abnormal timing • The motor lock signal remains LOW for a predetermined continuous period of time while the motor remains stationary.
Causes: K PC drum motor (M18) Printer control board (PRCB)
Remedy: 1 Check the M18 connector for proper connection and correct as necessary. 2 Check the M18 connector for proper drive coupling and correct as necessary. 3 Check the PRCB connector for proper connection and correct as necessary. 4 M18 operation check PRCB CN35-10 (REM) PRCB CN35-13 (LOCK) K-2 5 Change M18 6 PRCB ICP14 conduction check 7 Change PRCB

Code: C2350

Description: Toner suction fan motor’s failure to turn • The motor lock signal remains HIGH for a predetermined continuous period of time while the motor is turning.
Causes: Toner suction fan motor (FM7) Printer control board (PRCB)
Remedy: 1 Check the FM8 connector for proper connection and correct as necessary. 2 Check the fan for possible overload and correct as necessary. 3 FM7 operation check PRCB CN15-1 (REM) PRCB CN15-3 (LOCK) K-10 4 Change FM7 5 PRCB ICP6 conduction check 6 Change PRCB

Code: C2353

Description: IU cooling fan motor’s failure to turn • The motor lock signal remains HIGH for a predetermined continuous period of time while the motor is turning.
Causes: IU cooling fan motor (FM15) PH relay board (REYB/PH) Printer control board (PRCB)
Remedy: 1 Check the FM15 connector for proper connection and correct as necessary. 2 Check the fan for possible overload and correct as necessary. 3 FM15 operation check REYB/PH CN5-1 (REM) REYB/PH CN5-3 (LOCK) A to B-6 4 Change FM15 5 REYB/PH ICP1 conduction check 6 Change REYB/PH 7 Change PRCB

Code: C2354

Description: Rear side cooling fan motor’s failure to turn • The motor lock signal remains HIGH for a predetermined continuous period of time while the motor is turning.
Causes: Rear side cooling fan motor (FM16) Printer control board (PRCB)
Remedy: 1 Check the FM16 connector for proper connection and correct as necessary. 2 Check the fan for possible overload and correct as necessary. 3 FM16 operation check PRCB CN18-2 (REM) PRCB CN18-3 (LOCK) C-12 to 13 4 Change FM16 5 PRCB ICP7 conduction check 6 Change PRCB

Code: C2557

Description: Abnormally low toner density detected black TCR sensor • When sampling data is determined in TC ratio calculation control, TCR sensor output is higher than a predetermined value for a predetermined number of times in a row even though there is toner in the sub hopper.
Causes: Developing unit Toner cartridge Toner empty sensor/K (PZS/K) Toner supply motor/K (M12) Toner cartridge motor C/K (M14) Printer control board (PRCB)
Remedy: 1 Perform image troubleshooting procedure if image density is low. 2 M12 operation check (At this time, developing/drum unit must be non-installation.) PRCB CN19-13 to 16 C-20 3 M14 operation check PRCB CN20-9 to 12 K-8 4 Reinstall developing unit 5 Reinstall toner cartridge 6 If the toner empty sensor and its surroundings inside the sub hopper are dirtied with toner, clean them. 7 Change developing unit 8 Change PRCB.

Code: C2558

Description: Abnormally high toner density detected black TCR sensor • TC ratio in the developing unit, which is determined by toner replenishing amount control mechanism, is a predetermined value or more for a given number of times consecutively.
Causes: Developing unit Toner cartridge Sub hopper unit Printer control board (PRCB)
Remedy: 1 Reinstall developing unit 2 Reinstall toner cartridge 3 Change developing unit 4 PRCB ICP17 conduction check 5 Change PRCB 6 Change sub hopper unit

Code: C255C

Description: Black TCR sensor adjustment failure • TCR sensor automatic adjustment does not function properly, failing to adjust to an appropriate value.
Causes: Developing unit Printer control board (PRCB)
Remedy: 1 Reinstall developing unit 2 Change developing unit 3 PRCB ICP17 conduction check 4 Change PRCB

Code: C2564

Description: Black TCR sensor failure • Alarm signals for a TCR sensor are detected more than the predetermined number of times. This detection is used for detecting disconnection of TCR sensor connector.
Causes: Developing unit Printer control board (PRCB)
Remedy: 1 Reinstall developing unit 2 Check the harness from developing unit to PRCB for proper connection and correct as necessary. 3 Change developing unit 4 PRCB ICP2 conduction check 5 Change PRCB
Đăng ký nhận bản tin Đăng ký nhận bản tin Đăng ký nhận bản tin Đăng ký nhận bản tin
Đăng ký nhận bản tin
Nhận ưu đãi sớm nhất khi chương trình diễn ra

Đăng ký nhận bản tin

Việc cho phép sử dụng cookie sẽ giúp cải thiện trải nghiệm của bạn trên trang web này. Chính sách cookie