Thương hiệu phân phối chính hãng
Giỏ hàng

Mã lỗi Konica-Minolta bizhub 654 — Trang 13/24

Code: C4801

Description: Main unit board failure MFP detects simultaneous replacement of multiple boards.
Causes: • SSD board (SSDB) • Printer control board (PRCB)
Remedy: 1 Reinstall the old PRCB. 2 If the above actions do not solve the problem, contact KM.

Code: C4802

Description: Main unit backup data miscompare The replacement of the printer control board is detected.
Causes: Printer control board (PRCB)
Remedy: 1 1. When the finisher or job separator has been installed, remove it once. 2. Call the Enhanced Security in Service Mode to the screen. 3. Touch [Engine Data Backup]. 4. Touch [Engine Data Reflect mode], and press the Start key. 5. Select [Yes], and press the Start key again. 6. Check that the result “OK” appears. 7. Turn OFF the main power switch and turn it ON again more than 10 seconds after. 2 Update the PRCB firmware. 3 If the above actions do not solve the problem, contact KM.

Code: C5104

Description: Transfer belt motor's failure to turn The motor lock signal remains HIGH for a predetermined continuous period of time while the motor is turning.
Causes: • Transfer belt unit • Transfer belt motor (M1) • Printer control board (PRCB)
Remedy: 1 Check the connector between M1-PRCB CN21 for proper connection and correct as necessary. 2 Check the transfer belt for proper drive coupling and correct as necessary. 3 Check the drive gear of the transfer belt unit for rotation and correct any faulty rotation. 4 M1 operation check PRCB CN21-3 (REM) PRCB CN21-6 (LOCK) 17-K 5 Replace M1 6 Replace the transfer belt unit. 7 PRCB ICP7 or ICP18 conduction check 8 Replace PRCB

Code: C5105

Description: Transfer belt motor's turning at abnormal timing The motor lock signal remains LOW for a predetermined continuous period of time while the motor remains stationary.
Causes: • Transfer belt unit • Transfer belt motor (M1) • Printer control board (PRCB)
Remedy: 1 Check the connector between M1-PRCB CN21 for proper connection and correct as necessary. 2 Check the transfer belt for proper drive coupling and correct as necessary. 3 Check the drive gear of the transfer belt unit for rotation and correct any faulty rotation. 4 M1 operation check PRCB CN21-3 (REM) PRCB CN21-6 (LOCK) 17-K 5 Replace M1 6 Replace the transfer belt unit. 7 PRCB ICP7 or ICP18 conduction check 8 Replace PRCB

Code: C5304

Description: IH power supply cooling fan's failure to turn The fan lock signal remains HIGH for a predetermined continuous period of time while the fan is turning.
Causes: • IH power supply cooling fan (FM10) • Printer control board (PRCB)
Remedy: 1 Check the connector between FM10-relay CN293- PRCB CN5 for proper connection and correct as necessary. 2 Check the fan for possible overload and correct as necessary. 3 FM10 operation check PRCB CN5-1 (DRIVE) PRCB CN5-3 (LOCK) 9-K 4 Replace FM10 5 PRCB ICP24 conduction check 6 Replace PRCB

Code: C5306

Description: IH coil cooling fan's failure to turn The fan lock signal remains HIGH for a predetermined continuous period of time while the fan is turning.
Causes: • IH coil cooling fan (FM3) • Printer control board (PRCB)
Remedy: 1 Check the connector between FM3-relay CN324- PRCB CN2 for proper connection and correct as necessary. 2 Check the fan for possible overload and correct as necessary. 3 FM3 operation check PRCB CN2-7 (DRIVE) PRCB CN2-9 (LOCK) 3-K 4 Replace FM3 5 Replace PRCB

Code: C5351

Description: DC power supply cooling fan's failure to turn The fan lock signal remains HIGH for a predetermined continuous period of time while the fan is turning.
Causes: • DC power supply cooling fan (FM9) • DC power supply (DCPU) • Printer control board (PRCB)
Remedy: 1 Check the connector between FM9-relay CN333- PRCB CN38 for proper connection and correct as necessary. 2 Check the fan for possible overload and correct as necessary. 3 FM9 operation check PRCB CN38-1 (DRIVE) PRCB CN38-3 (LOCK) 19-K 4 Replace FM9 5 PRCB ICP3 conduction check 6 Replace DCPU 7 Replace PRCB

Code: C5354

Description: Ozone ventilation fan's failure to turn The fan lock signal remains HIGH for a predetermined continuous period of time while the fan is turning.
Causes: • Ozone ventilation fan motor (FM6) • Printer control board (PRCB)
Remedy: 1 Check the connector between FM6-relay CN322- PRCB CN1 for proper connection and correct as necessary. 2 Check the fan for possible overload and correct as necessary. 3 FM6 operation check PRCB CN1-6 (DRIVE) PRCB CN1-8 (LOCK) 7-K 4 Replace FM6 5 Replace PRCB
Đăng ký nhận bản tin Đăng ký nhận bản tin Đăng ký nhận bản tin Đăng ký nhận bản tin
Đăng ký nhận bản tin
Nhận ưu đãi sớm nhất khi chương trình diễn ra

Đăng ký nhận bản tin

Việc cho phép sử dụng cookie sẽ giúp cải thiện trải nghiệm của bạn trên trang web này. Chính sách cookie