• Code: CD704
• Description: Finisher Flash ROM device error (When FS-533, FS-534, FS-534SD or JS-506 is installed). An erase error or other device fault occurs during the finisher flash ROM writing.
• Causes: <When FS-533, FS-534 or FS-534SD is installed> • FS control board (FSCB) <When JS-506 is installed> • JS control board (JSCB)
• Remedy: When FS-533, FS-534 or FS-534SD is installed 1. Turn OFF the main power switch, disconnect and then connect the power cord. Wait for 10 sec. or more after connect the power cord, and turn ON the main power switch. 2. Rewrite the firmware. 3. Replace FSCB. (FS-533/FS-534/FS-534SD) When JS-506 is installed 1. Turn OFF the main power switch, disconnect and then connect the power cord. Wait for 10 sec. or more after connect the power cord, and turn ON the main power switch. 2. Rewrite the firmware. 3. Replace JSCB.

• Code: CD705, CD706
• Description: • CD705: Mechanical controller sub-CPU flash ROM device error • CD706: Mechanical controller sub-CPU flash ROM error • CD705: An erase error or other device fault occurs during mechanical controller sub-CPU flash ROM writing. • CD706: A data error is determined to exist in the mechanical controller sub-CPU flash ROM during starting.
• Causes: MFP board (MFPB)
• Remedy: 1. Turn OFF the main power switch, disconnect and then connect the power cord. Wait for 10 sec. or more after connect the power cord, and turn ON the main power switch. 2. Rewrite the firmware. 3. Replace MFPB.

• Code: CDF50, CDF70, CDFA0
• Description: • CDF50: ASIC image version failure • CDF70: ASIC image access failure • CDFA0: ASIC image error. Communication error is detected between the MFP board (MFPB) and the CCD board (CCDB).
• Causes: • MFP board (MFPB) • CCD board (CCDB)
• Remedy: 1. Check the connector between MFPB CN1-CCDB CN3 for proper connection and correct as necessary. 2. Rewrite the firmware. 3. Replace CCDB. 4. Replace MFPB.

• Code: CDF51, CDF71, CDFA1
• Description: CDF51: ASIC image version failure (back side) (When DF-704 is installed) CDF71: ASIC image access failure (back side) (When DF-704 is installed) CDFA1: ASIC image error (back side) (When DF-704 is installed). Communication error is detected between the MFP board (MFPB) and the dual scan image processing board (DSIPB).
• Causes: • MFP board (MFPB) • Dual scan image processing board (DSIPB; DF-704)
• Remedy: 1. Check the connector between MFPB CN22-DSIPB CN01 for proper connection and correct as necessary. 2. Rewrite the firmware. 3. Replace DSIPB. 4. Replace MFPB.

• Code: CE001 ... CE007
• Description: • CE001: Abnormal message queue • CE003: Task error • CE004: Event error • CE005: Memory access error • CE006: Header access error • CE007: DIMM initialize error
• Causes: MFP board (MFPB)
• Remedy: 1. Check the connectors on MFPB for proper connection and correct as necessary. 2. Replace MFPB.

• Code: CE002
• Description: Message and method parameter failure
• Causes: • MFP board (MFPB) • Hard disk (A) (HDD (A)) • Hard disk (B) (HDD (B): HD-524)
• Remedy: 1. Turn OFF the main power switch and turn it ON again, and conduct the following setting. [Service Mode] -> [System 1] -> [Initialization] -> [Clear All Data]. 2. Format the hard disk. 3. Replace the hard disk. (HDD (A) / HDD (B)) 4. Replace MFPB.

• Code: CE101
• Description: Browser finish detected • The browser is automatically recovered (restarted) after the main body detected that the browser (separate process) has stopped with fault. • When the “Malfunction finish is detected over predetermined number of times” or “the browser task process is except in idle (printing, etc)”.
• Causes: MFP board (MFPB)
• Remedy: 1. Check the connectors on MFPB for proper connection and correct as necessary. 2. Replace MFPB.

• Code: CE201
• Description: Transmission operation log storage fault. When the transmission log storage failed, it repeats retrial until transmission operation log is stored. The trouble is detected when the retrial failed for predetermined number of times.
• Causes: MFP board (MFPB)
• Remedy: 1. Check the connectors on MFPB for proper connection and correct as necessary. 2. Replace MFPB.