Thương hiệu phân phối chính hãng
Giỏ hàng

Mã lỗi Konica-Minolta bizhub C452 — Trang 20/28

Code: C6103

Description: Slider over running
• The scanner home sensor detects the scanner at its home position during a period of time that begins with the time when a pre-scan command and a scan preparation command are executed and ends when a home return command is executed.
Causes: Scanner home sensor (PS201) Scanner motor (M201) Scanner relay board (REYB/SCAN) MFP board (MFPB)
Remedy: 1 Correct or change the scanner drive (cable, pulley, gear, belt) if it is faulty. - - 2 Correct the scanner motor set screw if loose. - - 3 Adjust [Image Position Leading Edge] and [Feed Direction Adjustment]. - - 4 Check the PS201, M201, REYB/SCAN and MFPB connector for proper connection and correct as necessary. - - 5 PS201 I/O check, sensor check REYB/SCAN PJ3-5 (ON) P-17 6 M201 operation check REYB/SCAN PJ5-4 to 7 W-19 7 Change REYB/SCAN. - - 8 Change MFPB.

Code: C6104

Description: Opposed board home sensor abnormality (initial)
• The back side cleaning sensor (PS9) does not change from H to L even after the lapse of a given period of time after the home position detecting operation is started at the initial operation. • The back side cleaning sensor (PS9) does not change from L to H even after the lapse of a given period of time after the home position detecting operation is started at the initial operation.
Causes: Back side cleaning sensor (PS9) Back side cleaning motor (M7) DF control board (DFCB)
Remedy: 1 Check the motor and sensor connectors for proper connection, and correct as necessary. - - 2 Check the connector of M7 for proper drive coupling, and correct as necessary. - - 3 PS9 I/O check, sensor check DFCB PJ6-11 (ON) DF-619 C-6 4 M7 operation check DFCB PJ5-5 to 8 DF-619 C-7 5 Change M7 - - 6 DFCB ICP10 conduction check - - 7 Change DFCB

Code: C6105

Description: Opposed board home sensor abnormality (normal)
• At the time of operation other than the initial operation, the back side cleaning sensor (PS9) error is detected.
Causes: Back side cleaning sensor (PS9) Back side cleaning motor (M7) DF control board (DFCB)
Remedy: 1 Check the motor and sensor connectors for proper connection, and correct as necessary. - - 2 Check the connector of M7 for proper drive coupling, and correct as necessary. - - 3 PS9 I/O check, sensor check DFCB PJ6-11 (ON) DF-619 C-6 4 M7 operation check DFCB PJ5-5 to 8 DF-619 C-7 5 Change M7 - - 6 DFCB ICP10 conduction check - - 7 Change DFCB

Code: C6301

Description: Optical cooling fan motor’s failure to turn
• The fan lock signal remains HIGH for a predetermined continuous period of time while the motor remains stationary.
Causes: Optical cooling fan motor (M202) Scanner relay board (REYB/SCAN) MFP board (MFPB)
Remedy: 1 Check the FM201 connector for proper connection and correct as necessary. - - 2 Check the fan for possible overload and correct as necessary. - - 3 M202 operation check REYB/SCAN PJ4-3 (LOCK) P-18 4 Change REYB/SCAN - - 5 Change MFPB

Code: C6303

Description: CIS cooling fan motor’s failure to turn
• While the motor is running, the fan lock signal remains HIGH three times for a predetermined period of consecutive time.
Causes: CIS Cooling fan motor (FM2) DF control board (DFCB)
Remedy: 1 Check the FM2 connector for proper connection and correct as necessary. - - 2 Check the fan for possible overload and correct as necessary. - - 3 FM2 operation check DFCB PJ12-4 to 6 DF-619 K-9 4 Change FM2 - - 5 DFCB ICP5 conduction check - - 6 Change DFCB

Code: C6704

Description: Image input time out
• Image data is not input from the scanner to the MFP board (MFPB).
Causes: MFP board (MFPB) CCD board (CCDB)
Remedy: 1 Select [Service Mode] - [State Confirmation] - [Memory/HDD Adj.] - [Memory Bus Check] - [Scanner-Memory], and conduct the memory bus function. . . 2 Check the connectors between scanner section and MFPB for proper connection and correct as necessary. . . 3 Change MFPB . . 4 Change CCDB

Code: C6751

Description: CCD clamp/gain adjustment failure
• The adjustment value is 0 or 255 during a CCD clamp adjustment. • The peak value of the output data is 64 or less during a CCD gain adjustment.
Causes: Exposure unit CCD board (CCDB) MFP board (MFPB)
Remedy: 1 Correct the harness connection between CCDB and MFPB if faulty. - - 2 Check for possible extraneous light and correct as necessary. - - 3 Clean the lens, mirrors, CCD surface, and shading sheet if dirty - - 4 Correct reflective mirror of the scanner if faulty, or change scanner. - - 5 Change CCDB - - 6 Change MFPB

Code: C6752

Description: ASIC clock input error (front side)
• When starting the scanner, verification on reading and writing the predetermined value for image processing ASIC on CCD board was conducted, and verification failure was detected.
Causes: Exposure unit CCD board (CCDB) MFP board (MFPB)
Remedy: 1 Correct the harness connection of CCDB if faulty. - - 2 Change CCDB - - 3 Change MFPB
Đăng ký nhận bản tin Đăng ký nhận bản tin Đăng ký nhận bản tin Đăng ký nhận bản tin
Đăng ký nhận bản tin
Nhận ưu đãi sớm nhất khi chương trình diễn ra

Đăng ký nhận bản tin

Việc cho phép sử dụng cookie sẽ giúp cải thiện trải nghiệm của bạn trên trang web này. Chính sách cookie