Thương hiệu phân phối chính hãng
Giỏ hàng

Mã lỗi Konica-Minolta bizhub C452 — Trang 6/28

Code: C1145

Description: End stopper drive motor malfunction
<When FS-526 is installed> • The 2 staples trail edge stopper home sensor (PS22) is turned neither ON nor OFF even after the set period of time has elapsed after the 2 staples trail edge stopper motor (M19) is turned ON. • The 2 staples trail edge stopper standby sensor/1 (PS23) is turned neither ON nor OFF even after the set period of time has elapsed after the 2 staples trail edge stopper motor (M19) is turned ON. • The 2 staples trail edge stopper standby sensor/2 (PS42) is turned neither ON nor OFF even after the set period of time has elapsed after the 2 staples trail edge stopper motor (M19) is turned ON.
Causes: 2 staples trail edge stopper motor (M19) 2 staples trail edge stopper home sensor (PS22) 2 staples trail edge stopper standby sensor/1 (PS23) 2 staples trail edge stopper standby sensor/2 (PS42) FS control board (FSCB)
Remedy: 1 Check the motor and sensor connectors for proper connection, and correct as necessary. - - 2 Check the connector of M19 for proper drive coupling, and correct as necessary. - - 3 PS22 I/O check, sensor check FSCB CN20<A>-15 (ON) FS-526 L-12 4 PS23 I/O check, sensor check FSCB CN20<A>-18 (ON) FS-526 L-12 to 13 5 PS42 I/O check FSCB CN20<A>-9 (ON) FS-526 L-12 6 M19 operation check FSCB CN19-9 to 12 FS-526 D-13 7 Change M19 - - 8 Change FSCB

Code: C1150

Description: Center-staple rear adjust drive motor malfunction <When FS-526+SD-508 is installed>
• The center staple alignment motor home sensor/R (PS31) is turned neither ON nor OFF even after the set period of time has elapsed after the center staple alignment motor /R (M21) is turned ON. <When FS-527+SD-509 is installed> • The center staple alignment home sensor/R (PS41) is turned neither ON nor OFF even after the set period of time has elapsed after the center staple alignment motor/R (M23) is turned ON.
Causes: When FS-526+SD-508 is installed: Center staple alignment motor /R (M21) Center staple alignment motor home sensor/R (PS31) SD drive board (SDDB) FS control board (FSCB).
When FS-527+SD-509 is installed: Center staple alignment motor/R (M23) Center staple alignment home sensor/R (PS41) SD drive board (SDDB) FS control board (FSCB)
Remedy: When FS-526+SD-508 is installed: 1 Check the motor and sensor connectors for proper connection, and correct as necessary. - - 2 Check the connector of M21 for proper drive coupling, and correct as necessary. - - 3 PS31 I/O check, sensor check SDDB CN403-14 (ON) SD-508 C-9 4 M21 operation check SDDB CN403-5 to 8 SD-508 C-9 5 Change M21 - - 6 SDDB ICP4 conduction check - - 7 Change SDDB - - 8 Change FSCB
When FS-527+SD-509 is installed: 1 Check the motor and sensor connectors for proper connection, and correct as necessary. - - 2 Check the connector of M23 for proper drive coupling, and correct as necessary. - - 3 PS41 I/O check, sensor check SDDB PJ9-3 (ON) SD-509 G-2 4 M23 operation check SDDB P7-5 to 8 SD-509 G-2 5 Change M23 - - 6 Change SDDB - - 7 Change FSCB

Code: C1151

Description: Center-staple stapler drive motor malfunction
<When FS-526+SD-508 is installed> • The stapler home sensor (PS33) is turned neither ON nor OFF even after the set period of time has elapsed after the center staple motor (M23) is turned ON.
Causes: Center staple motor (M23) Stapler home sensor (PS33) SD drive board (SDDB) FS control board (FSCB)
Remedy: 1 Check the motor and sensor connectors for proper connection, and correct as necessary. - - 2 Check the connector of M23 for proper drive coupling, and correct as necessary. - - 3 PS33 I/O check, sensor check SDDB CN403-17 (ON) SD-508 C-10 4 M23 operation check SDDB CN406<A>-1 to 4 (ON) SD-508 K-8 5 Change M23 - - 6 SDDB ICP4 conduction check - - 7 Change SDDB - - 8 Change FSCB

Code: C1152

Description: Center-staple paper exit motor malfunction
<When FS-526+SD-508 is installed> • The exit motor (M34) lock signal remains set to H for a set period of time while the exit motor (M34) is turning.
Causes: Exit motor (M34) SD drive board (SDDB) FS control board (FSCB)
Remedy: 1 Check the motor and sensor connectors for proper connection, and correct as necessary. - - 2 Check the connector of M34 for proper drive coupling, and correct as necessary. - - 3 M34 operation check - SD-508 G-3 to 4 4 Change M34 - - 5 SDDB ICP12 conduction check - - 6 Change SDDB - - 7 Change FSCB

Code: C1153

Description: Center-staple paddle up-down motor malfunction
<When FS-526+SD-508 is installed> • The paddle home sensor/C (PS37) is turned neither ON nor OFF even after the set period of time has elapsed after the center staple paddle lift motor/C (M26) is turned ON.
Causes: Center staple paddle lift motor/C (M26) Paddle home sensor/C (PS37) SD drive board (SDDB) FS control board (FSCB)
Remedy: 1 Check the motor and sensor connectors for proper connection, and correct as necessary. - - 2 Check the connector of M26 for proper drive coupling, and correct as necessary. - - 3 PS37 I/O check, sensor check SDDB CN406<A>-11 (ON) SD-508 K-9 4 M26 operation check SDDB CN406<A>-5 to 8 SD-508 K-8 5 Change M26 - - 6 SDDB ICP4 conduction check - - 7 Change SDDB - - 8 Change FSCB

Code: C1156

Description: Center-staple paddle roller motor malfunction (trailing edge)
<When FS-526+SD-508 is installed> • The center staple paddle/T (M29) lock signal remains set to L for a set period of time while the center staple paddle/T (M29) is turning. <When FS-527+SD-509 is installed> • Even after the set period of time has elapsed after the upper paddle motor (M21) starts running, a change of motor lock signal is not detected and neither the paper detection sensor/1 (PS43) nor the paper detection sensor/2 (PS44) is turned ON.
Causes: When FS-526+SD-508 is installed: Center staple paddle/T (M29) SD drive board (SDDB) FS control board (FSCB).
When FS-527+SD-509 is installed: Upper paddle motor (M21) Paper detection sensor/1 (PS43) Paper detection sensor/2 (PS44) SD drive board (SDDB) FS control board (FSCB)
Remedy: When FS-526+SD-508 is installed: 1 Check the motor and sensor connectors for proper connection, and correct as necessary. - - 2 Check the connector of M29 for proper drive coupling, and correct as necessary. - - 3 M29 operation check SDDB CN404-1 to 5 SD-508 C-8 4 Change M29 - - 5 SDDB ICP5 conduction check - - 6 Change SDDB - - 7 Change FSCB.
When FS-527+SD-509 is installed: 1 Check the motor and sensor connectors for proper connection, and correct as necessary. - - 2 Check the connector of M21 for proper drive coupling, and correct as necessary. - - 3 PS43 I/O check, sensor check SDDB PJ9-8 (ON) SD-509 G-1 4 PS44 I/O check, sensor check SDDB PJ13-2 (ON) SD-509 G-3 5 M21 operation check SDDB PJ5-6 to 10 SD-509 B-3 6 Change M21 - - 7 Change SDDB - - 8 Change FSCB

Code: C1157

Description: Center-staple paddle roller motor malfunction (middle)
<When FS-526+SD-508 is installed> • The center staple paddle/C (M30) lock signal remains set to L for a set period of time while the center staple paddle/C (M30) is turning.
Causes: Center staple paddle/C (M30) SD drive board (SDDB) FS control board (FSCB)
Remedy: 1 Check the motor and sensor connectors for proper connection, and correct as necessary. - - 2 Check the connector of M30 for proper drive coupling, and correct as necessary. - - 3 M30 operation check SDDB CN406<B>-11 to 15 SD-508 K-10 4 Change M30 - - 5 SDDB ICP5 conduction check - - 6 Change SDDB - - 7 Change FSCB

Code: C1158

Description: Center-staple paddle roller motor malfunction (leading edge)
<When FS-527+SD-509 is installed>• Even after the set period of time has elapsed after the lower paddle motor (M22) starts running, a change of motor lock signal is not detected and neither the paper detection sensor/1 (PS43) nor the paper detection sensor/2 (PS44) is turned ON.
Causes: lower paddle motor (M22) Paper detection sensor/1 (PS43) Paper detection sensor/2 (PS44) SD drive board (SDDB) FS control board (FSCB)
Remedy: 1 Check the motor and sensor connectors for proper connection, and correct as necessary. - - 2 Check the connector of M22 for proper drive coupling, and correct as necessary. - - 3 PS43 I/O check, sensor check SDDB PJ9-8 (ON) SD-509 G-1 4 PS44 I/O check, sensor check SDDB PJ13-2 (ON) SD-509 G-3 5 M22 operation check SDDB PJ5-1 to 5 SD-509 B-4 6 Change M22 - - 7 Change SDDB - - 8 Change FSCB
Đăng ký nhận bản tin Đăng ký nhận bản tin Đăng ký nhận bản tin Đăng ký nhận bản tin
Đăng ký nhận bản tin
Nhận ưu đãi sớm nhất khi chương trình diễn ra

Đăng ký nhận bản tin

Việc cho phép sử dụng cookie sẽ giúp cải thiện trải nghiệm của bạn trên trang web này. Chính sách cookie