• Code: CC15B
• Description: Flash ROM error (saddle) <When FS-534+SD-511 is installed> <When FS-535+SD-512 is installed> Data of flash ROM of the saddle is determined to be faulty when the main power switch is turned ON.
• Remedy: 1 Turn OFF the main power switch, disconnect and then connect the power cord. Wait for 10 sec. or more after connect the power cord, and turn ON the main power switch. - - 2 Rewrite the firmware. - - 3 Replace SDDB (SD-511/SD-512)

• Code: CC15C
• Description: Engine Flash ROM writing error. Data of flash ROM of the engine is determined to be faulty.
• Remedy: 1 Turn OFF the main power switch, disconnect and then connect the power cord. Wait for 10 sec. or more after connect the power cord, and turn ON the main power switch. - - 2 Rewrite the firmware. - - 3 Replace PRCB

• Code: CC163
• Description: ROM contents error (PRT). The wrong model of firmware is detected in the engine during the initial connection to the engine is being checked.
• Remedy: • SSD board (SSDB) • Printer control board (PRCB) 1 Rewrite the firmware. - - 2 Replace PRCB - - 1. Turn OFF the main power switch and replace the current PRCB with a new one. 2. Update the PRCB firmware. 3. After completing the firmware update, turn OFF and ON the main power switch and check to see that warm-up is started. 4. When the trouble cannot be solved, reinstall the removed PRCB to the original board. NOTE • When taking the above steps, check whether PRCB is defective or not without replacing the SSDB. 3 If the above actions do not solve the problem, contact KM.

• Code: CC164
• Description: ROM contents error (MSC) • The wrong model of firmware is detected in the MFP board when the main power switch is turned ON. • The machine type information (Machine, Type) registered to the machine differs from the actual machine type.
• Remedy: • Printer control board (PRCB) • MFP board (MFPB) 1 Check the ROM version. - - 2 Check the machine type information registered and reenter as necessary. For details the machine information, see “J.2.4 Entering the machine type information”. - - 3 Rewrite the firmware. - - 4 Replace the corresponding board. - - 5 If the above actions do not solve the problem, contact KM.

• Code: CC165
• Description: ROM contents error (DF) When the power is turned ON, DF control board or firmware error is detected.
• Remedy: DF control board (DFCB) 1 Turn OFF the main power switch, disconnect and then connect the power cord. Wait for 10 sec. or more after connect the power cord, and turn ON the main power switch. - - 2 Rewrite the firmware. - - 3 Replace DFCB

• Code: CC170...CC186
• Description: Dynamic link error during starting (AP0) Dynamic link error during starting (AP1) Dynamic link error during starting (AP2) Dynamic link error during starting (AP3) Dynamic link error during starting (AP4) Dynamic link error during starting (LDR) Dynamic link error during starting (IBR) Dynamic link error during starting (IID) Dynamic link error during starting (IPF) Dynamic link error during starting (IMY) Dynamic link error during starting (SPF) Dynamic link error during starting (OAP) A dynamic link error occurs in the program on the MFP board due to an insufficient memory space available, a ROM fault, or other reason when the main power switch is turned ON.
• Remedy: 1 If the malfunction code “C-C172” has occurred, access [Service Mode] -> [System 2] -> [Image Controller Setting] and check to see if “Controller 2,” “Controller 3,” or “Others” is set for [Image Controller Setting]. If any of these is set, according to the kind of controller, select “Controller 0” or “Controller 1.” 2 If the malfunction code "C-C180" has occurred, check to install the appropriate loadable device driver for an authentication unit which is installed to the MFP. When the appropriate loadable device driver is not installed, reinstall the appropriate loadable device driver. - - 3 Replace MFPB - - 4 If the above actions do not solve the problem, contact KM.

• Code: CC190
• Description: Outline font load error. An error occurred while loading the outline font.
• Remedy: • MFP board (MFPB) • Hard disk 1 Check the connector between hard disk-MFPB PJ11 for proper connection and correct as necessary. - - 2 Format hard disk. - - 3 Replace the hard disk. - - 4 Replace MFPB

• Code: CC191
• Description: Setting parameter load error (LDR) Upon startup, the processing of the loadable device driver setting data file failed. • RAM disk file creation failed. • Reading from the flash ROM failed. • An error occurred in API of the authentication module.
• Remedy: 1 Turn OFF the main power switch, wait for 10 sec. or more, and turn ON the main power switch. - - 2 Reinstall the loadable device driver. - - 3 Rewrite the firmware. - - 4 Replace MFPB