Thương hiệu phân phối chính hãng
Giỏ hàng

Mã lỗi Kyocera FS3540MFP — Trang 4/6

Code: 5100

Description: Main charger high-voltage error
Five pages have been printed with the main charger output short-circuited.
Causes: Drum unit installed incorrectly. Engine PWB installed incorrectly. Defective engine PWB.
Remedy: Drum unit installed incorrectly. Verify harness is not pinched.
Engine PWB installed incorrectly. Verify harness is not pinched.
Defective engine PWB. Replace the engine PWB and check for correct operation.

Code: 6000

Description: Broken fuser heater wire
The temperature does not reach 100°C/212°F after the fuser heater has been turned on continuously for 30 s. The temperature does not rise by 1°C/1.8°F after the fuser heater lamp has been turned on continuously for 15 s during warm-up or at standby.(Only when the detection temperature is less than 200°C.)
Causes: Defective connector cable or poor contact in the connector. Fuser thermostat triggered. Broken fuser heater wire.
Remedy: Defective connector cable or poor contact in the connector. Reinsert the connector. Also check for continuity within the connector cable. If none, remedy or replace the cable. Fuser heater and power source PWB (YC102) Fuser unit and engine PWB (YC506)
Fuser thermostat triggered. Reinsert the fuser unit.
Broken fuser heater wire. Replace the fuser unit.

Code: 6020

Description: Abnormally high fuser thermistor 2 temperature
The temperature of the fuser thermistor 2 detects 250°C/482°F or more continuously for 3 s.
Causes: Shorted fuser thermistor 2. Defective engine PWB.
Remedy: Shorted fuser thermistor 2. Replace the fuser unit.
Defective engine PWB. Replace the engine PWB and check for correct operation.

Code: 6030

Description: Broken fuser thermistor 2 wire
average AD value input from fuser thermistor 2 for 1.8 seconds is less than one. (Only when the detection temperature is 50°C or more.)
Causes: Defective connector cable or poor contact in the connector. Broken fuser thermistor 2 wire. Fuser thermostat triggered. Broken fuser heater wire.
Remedy: Defective connector cable or poor contact in the connector. Reinsert the connector. Also check for continuity within the connector cable. If none, remedy or replace the cable. Fuser unit and engine PWB (YC506)
Broken fuser thermistor 2 wire. Replace the fuser unit.
Fuser thermostat triggered. Reinsert the fuser unit.
Broken fuser heater wire. Replace the fuser unit.

Code: 6220

Description: Abnormally high fuser thermistor 1 temperature
The temperature of the fuser thermistor 1 detects 255°C/491°F or more continuously for 3 s.
Causes: Shorted fuser thermistor 1. Defective engine PWB.
Remedy: Shorted fuser thermistor 1. Replace the fuser unit.
Defective engine PWB. Replace the engine PWB and check for correct operation.

Code: 6230

Description: Broken fuser thermistor 1 wire
average AD value input from fuser thermistor 1 for 1.8 seconds is less than one.
Causes: Defective connector cable or poor contact in the connector. Broken fuser thermistor 1 wire. Fuser thermostat triggered. Broken fuser heater wire.
Remedy: Defective connector cable or poor contact in the connector. Reinsert the connector. Also check for continuity within the connector cable. If none, remedy or replace the cable. Fuser unit and engine PWB (YC506)
Broken fuser thermistor 1 wire. Replace the fuser unit.
Fuser thermostat triggered. Reinsert the fuser unit.
Broken fuser heater wire. Replace the fuser unit.

Code: 6400

Description: Zero-cross signal error
The zero-cross signal does not reach the engine PWB for more than 2 s.
Causes: Defective connector cable or poor contact in the connector. Defective power source PWB. Defective engine PWB.
Remedy: Defective connector cable or poor contact in the connector. Reinsert the connector. Also check for continuity within the connector cable. If none, remedy or replace the cable. Power source PWB (YC103) and connect-L PWB (YC1) Connect-L PWB (YC8) and engine PWB (YC503)
Defective power source PWB. Replace the power source PWB and check for correct operation.
Defective engine PWB. Replace the engine PWB and check for correct operation.

Code: 7000

Description: Toner motor lock error
During driving the toner motor, a motor overcurrent signal is detected for 5 s.
Causes: Lump of toner inside toner container. Defective drive transmission system of the toner motor. Defective toner motor. Defective engine PWB.
Remedy: Lump of toner inside toner container. Replace the toner container.
Defective drive transmission system of the toner motor. Replace the developing unit.
Defective toner motor. Replace the developing unit.
Defective engine PWB. Replace the engine PWB and check for correct operation.
Đăng ký nhận bản tin Đăng ký nhận bản tin Đăng ký nhận bản tin Đăng ký nhận bản tin
Đăng ký nhận bản tin
Nhận ưu đãi sớm nhất khi chương trình diễn ra

Đăng ký nhận bản tin

Việc cho phép sử dụng cookie sẽ giúp cải thiện trải nghiệm của bạn trên trang web này. Chính sách cookie