Thương hiệu phân phối chính hãng
Giỏ hàng

Mã lỗi Kyocera FSC8520MFP — Trang 8/15

Code: 6000

Description: Broken fuser heater wire
Fuser thermistor 2 does not reach 80° C/176 °F even after20 s during warming up. The detected temperature of fuser thermistor2 does not reach the specified temperature (ready indication temperature) for 200 s in warming up after reached to 80° C/176 °F.
Causes: Defective connector cable or poor contact in the connector. Deformed connector pin. Defective IH PWB. Fuser thermostat triggered. Broken fuser heater wire. Defective engine PWB.
Remedy: Defective connector cable or poor contact in the connector. Reinsert the connector. Also check for continuity within the connector cable. If none, replace the cable. IH coil unit and IHPWB IHPWB and engine PWB (YC7)
Deformed connector pin. If the I/F connector pins of the fuser unit and the main unit are deformed owing to foreign matters, such as paper dusts, replace the connectors or the units including the connectors.
Defective IH PWB. Replace the IH PWB and check for correct operation.
Fuser thermostat triggered. Broken fuser heater wire. Reinsert the fuser unit.
Defective engine PWB. Replace the engine PWB and check for correct operation.

Code: 6020

Description: Abnormally high fuser thermistor 2 (center) temperature
The fuser thermistor 2 detects a temperature higher than 240°C/464°F continuously for 1 s.
Causes: Deformed connector pin. Shorted fuser thermistor. Defective engine PWB.
Remedy: Deformed connector pin. If the I/F connector pins of the fuser unit and the main unit are deformed owing to foreign matters, such as paper dusts, replace the connectors or the units including the connectors.
Shorted fuser thermistor. Replace the fuser unit.
Defective engine PWB. Replace the engine PWB and check for correct operation.

Code: 6030

Description: Fuser thermistor 2 (center) break error
A/D value of the fuser thermistor 2 exceeds 1010 bit continuously for 1 s during warming up.
Causes: Defective connector cable or poor contact in the connector. Deformed connector pin. Defective fuser thermistor. Defective engine PWB.
Remedy: Defective connector cable or poor contact in the connector. Reinsert the connector. Also check for continuity within the connector cable. If none, replace the cable. Fuser thermister2 and fuser PWB (YC2) Fuser unit and engine PWB (YC22)
Deformed connector pin. If the I/F connector pins of the fuser unit and the main unit are deformed owing to foreign matters, such as paper dusts, replace the connectors or the units including the connectors.
Defective fuser thermistor. Replace the fuser unit.
Defective engine PWB. Replace the engine PWB and check for correct operation.

Code: 6040

Description: NC sensor error
When a sensor detected the temperature higher than 150 °C/302 °F continuously for 5 seconds.
Causes: Deformed connector pin. Shorted fuser thermistor. Defective engine PWB.
Remedy: Deformed connector pin. If the I/F connector pins of the fuser unit and the main unit are deformed owing to foreign matters, such as paper dusts, replace the connectors or the units including the connectors.
Shorted fuser thermistor. Replace the fuser unit.
Defective engine PWB. Replace the engine PWB and check for correct operation.

Code: 6050

Description: Abnormally low fuser thermistor 2 (center) temperature
The fuser temperature lower than 100 °C/212 °F is detected continuously for 1 s during printing.
Causes: Deformed connector pin. Defective fuser thermistor. Defective fuser heater. Defective engine PWB.
Remedy: Deformed connector pin. If the I/F connector pins of the fuser unit and the main unit are deformed owing to foreign matters, such as paper dusts, replace the connectors or the units including the connectors.
Defective fuser thermistor. Defective fuser heater. Replace the fuser unit
Defective engine PWB. Replace the engine PWB and check for correct operation.

Code: 6120

Description: Abnormally high fuser thermistor 3 (press roller) temperature
The fuser temperature exceeds 200 °C/392 °F for 1 s.
Causes: Deformed connector pin. Defective IH PWB. Defective fuser thermistor. Defective engine PWB.
Remedy: Deformed connector pin. If the I/F connector pins of the fuser unit and the main unit are deformed owing to foreign matters, such as paper dusts, replace the connectors or the units including the connectors.
Defective IH PWB. Replace the IH PWB and check for correct operation.
Defective fuser thermistor. Replace the fuser unit.
Defective engine PWB. Replace the engine PWB and check for correct operation.

Code: 6130

Description: Fuser thermistor 3 (press roller) break error
Fuser thermistor 3 does not reach 30° C/86 °F even after60 s during warming up. The detected temperature of fuser thermistor3 does not reach the specified temperature (ready indication temperature) for 200 s in warming up after reached to 30° C/86 °F.
Causes: Defective connector cable or poor contact in the connector. Deformed connector pin. Defective IH PWB. Defective fuser thermistor. Defective engine PWB.
Remedy: Defective connector cable or poor contact in the connector. Reinsert the connector. Also check for continuity within the connector cable. If none, replace the cable. Fuser thermistor 3 and fuser PWB (YC4) Fuser unit and engine PWB (YC22)
Deformed connector pin. If the I/F connector pins of the fuser unit and the main unit are deformed owing to foreign matters, such as paper dusts, replace the connectors or the units including the connectors.
Defective IH PWB. Replace the IH PWB and check for correct operation.
Defective fuser thermistor. Replace the fuser unit.
Defective engine PWB. Replace the engine PWB and check for correct operation.

Code: 6150

Description: Abnormally low fuser thermistor 3 (press roller) temperature
The fuser temperature lower than 30 °C/86 °F is detected continuously for 1 s.
Causes: Deformed connector pin. Defective fuser thermistor. Defective fuser heater. Defective engine PWB.
Remedy: Deformed connector pin. If the I/F connector pins of the fuser unit and the main unit are deformed owing to foreign matters, such as paper dusts, replace the connectors or the units including the connectors.
Defective fuser thermistor. Defective fuser heater. Replace the fuser unit.
Defective engine PWB. Replace the engine PWB and check for correct operation.
Đăng ký nhận bản tin Đăng ký nhận bản tin Đăng ký nhận bản tin Đăng ký nhận bản tin
Đăng ký nhận bản tin
Nhận ưu đãi sớm nhất khi chương trình diễn ra

Đăng ký nhận bản tin

Việc cho phép sử dụng cookie sẽ giúp cải thiện trải nghiệm của bạn trên trang web này. Chính sách cookie