• Code: 5101
• Description: Main high-voltage error K
  Measure the inflowing current when Vpp is varied in 3 steps and verify if the difference of the currents of 0 and step 2 is less than 42 (51 if lower highvoltage board).
• Causes: Improper installation charger roller unit K. Defective connector cable or poor contact in the connector. Defective high voltage PWB 1. Defective engine PWB.
• Remedy: Improper installation charger roller unit K. Reinstall the charger roller unit K.
  Defective connector cable or poor contact in the connector. Reinsert the connector. Also check for continuity within the connector cable. If none, replace the cable. High voltage PWB 1 (YC4) and engine PWB (YC17)
  Defective high voltage PWB 1. Replace the high voltage PWB 1 and check for correct operation.
  Defective engine PWB. Replace the engine PWB and check for correct operation.

• Code: 5102
• Description: Main high-voltage error C
  Measure the inflowing current when Vpp is varied in 3 steps and verify if the difference of the currents of 0 and step 2 is less than 42 (51 if lower highvoltage board).
• Causes: Improper installation charger roller unit C. Defective connector cable or poor contact in the connector. Defective high voltage PWB 1. Defective engine PWB.
• Remedy: Improper installation charger roller unit C. Reinstall the charger roller unit C.
  Defective connector cable or poor contact in the connector. Reinsert the connector. Also check for continuity within the connector cable. If none, replace the cable. High voltage PWB 1 (YC2) and engine PWB (YC16)
  Defective high voltage PWB 1. Replace the high voltage PWB 1 and check for correct operation.
  Defective engine PWB. Replace the engine PWB and check for correct operation.

• Code: 5103
• Description: Main high-voltage error M
  Measure the inflowing current when Vpp is varied in 3 steps and verify if the difference of the currents of 0 and step 2 is less than 42 (51 if lower highvoltage board).
• Causes: Improper installation charger roller unit M. Defective connector cable or poor contact in the connector. Defective high voltage PWB 1. Defective engine PWB.
• Remedy: Improper installation charger roller unit M. Reinstall the charger roller unit M.
  Defective connector cable or poor contact in the connector. Reinsert the connector. Also check for continuity within the connector cable. If none, replace the cable. High voltage PWB 1 (YC3) and engine PWB (YC17)
  Defective high voltage PWB 1. Replace the high voltage PWB 1 and check for correct operation.
  Defective engine PWB. Replace the engine PWB and check for correct operation.

• Code: 5104
• Description: Main high-voltage error Y
  Measure the inflowing current when Vpp is varied in 3 steps and verify if the difference of the currents of 0 and step 2 is less than 42 (51 if lower highvoltage board).
• Causes: Improper installation charger roller unit Y. Defective connector cable or poor contact in the connector. Defective high voltage PWB 1. Defective engine PWB.
• Remedy: Improper installation charger roller unit Y. Reinstall the charger roller unit Y.
  Defective connector cable or poor contact in the connector. Reinsert the connector. Also check for continuity within the connector cable. If none, replace the cable. High voltage PWB 1 (YC1) and engine PWB (YC16)
  Defective high voltage PWB 1. Replace the high voltage PWB 1 and check for correct operation.
  Defective engine PWB. Replace the engine PWB and check for correct operation.

• Code: 6000
• Description: Broken fuser heater wire
  Fuser thermistor 1 does not reach 100° C/212 °F even after 60 s during warming up. The detected temperature of fuser thermistor 1 does not reach the specified temperature (ready indication temperature) for 420 s in warming up after reached to 100° C/212 °F.
• Causes: Defective connector cable or poor contact in the connector. Fuser thermostat triggered. Defective fuser IH. Defective engine PWB.
• Remedy: Defective connector cable or poor contact in the connector. Reinsert the connector. Also check for continuity within the connector cable. If none, replace the cable. Power source PWB (YC3) and fuser IH PWB (YC1) Fuser IH PWB (YC4) and engine PWB (YC26)
  Fuser thermostat triggered. Replace the fuser unit.
  Defective fuser IH. Replace the fuser unit.
  Defective engine PWB. Replace the engine PWB and check for correct operation.

• Code: 6020
• Description: Abnormally high fuser thermistor 1 temperature
  Fuser thermistor 1 detects a temperature higher than 240°C/464°F for 1 s.
• Causes: Defective connector cable or poor contact in the connector. Shorted fuser thermistor 1. Defective engine PWB.
• Remedy: Defective connector cable or poor contact in the connector. Reinsert the connector. Also check for continuity within the connector cable. If none, replace the cable. Fuser unit and engine PWB (YC26)
  Shorted fuser thermistor 1. Replace the fuser unit.
  Defective engine PWB. Replace the engine PWB and check for correct operation.

• Code: 6030
• Description: Broken fuser thermistor 1 wire
  Input from fuser thermistor 1 is 984 or more (A/D value) continuously for 1 s. Verify if A/D read in the differential output won’t change by 4 or more when it was turned on for 10 seconds in a lowtemperature environment.
• Causes: Defective connector cable or poor contact in the connector. Broken fuser thermistor 1 wire. Fuser thermostat triggered. Defective fuser IH. Defective engine PWB.
• Remedy: Defective connector cable or poor contact in the connector. Reinsert the connector. Also check for continuity within the connector cable. If none, replace the cable. Fuser unit and engine PWB (YC26)
  Broken fuser thermistor 1 wire. Replace the fuser unit.
  Fuser thermostat triggered. Replace the fuser unit.
  Defective fuser IH. Replace the fuser unit.
  Defective engine PWB. Replace the engine PWB and check for correct operation.

• Code: 6040
• Description: Fuser heater error
  Input from fuser thermistor 1 is abnormal value continuously for 1 s.
• Causes: Defective connector cable or poor contact in the connector. Broken fuser thermistor 1 wire. Defective fuser IH. Defective engine PWB.
• Remedy: Defective connector cable or poor contact in the connector. Reinsert the connector. Also check for continuity within the connector cable. If none, replace the cable. Fuser unit and engine PWB (YC26)
  Broken fuser thermistor 1 wire. Replace the fuser unit.
  Defective fuser IH. Replace the fuser unit.
  Defective engine PWB. Replace the engine PWB and check for correct operation.