Thương hiệu phân phối chính hãng
Giỏ hàng

Mã lỗi Kyocera KM4530 — Trang 5/6

Code: C5610

Description: Drum surface potential problem 2 • Minimizing the grid output cannot set the potential.
Causes: Defective high voltage transformer PCB.
Remedy: Replace the high voltage transformer PCB and check for correct operation.

Code: C6000

Description: Broken fixing heater wire • The fixing temperature does not increase for 40 s after the fixing heaters have been turned on for warming up. • The fixing temperature remains below 50C/122F for 10 s continuously after the fixing heaters have been turned on during stabilization.
Causes: Poor contact in the fixing unit thermistor connector terminals. Fixing unit thermistor installed incorrectly. Fixing unit thermostat triggered. Fixing heater M and S installed incorrectly. Broken fixing heater M and S wire.
Remedy: Check the connection of connector CN25 on the engine PCB and the continuity across the connector terminals. Repair or replace if necessary. Check and reinstall if necessary. Check for continuity. If none, replace the fixing unit thermostat. Check and reinstall if necessary. Check for continuity. If none, replace the fixing heater M and S.

Code: C6020

Description: Abnormally high fixing unit thermistor temperature • The fixing temperature exceeds 220C/446 F for 10 s. • The fixing unit temperature detection circuit on the engine PCB detects and abnormally high temperature.
Causes: Shorted fixing unit thermistor. Broken fixing heater control circuit on the power source PCB.
Remedy: Measure the resistance. If it is 0 Ω, replace the fixing unit thermistor. Replace the power source PCB and check for correct operation.

Code: C6030

Description: Broken fixing unit thermistor • The fixing temperature remains at 0C/32F for 30 s continuously when the fixing heater is on.
Causes: Poor contact in the fixing unit thermistor connector terminals. Broken fixing unit thermistor.
Remedy: Check the connection of connector CN25 on the engine PCB and the continuity across the connector terminals. Repair or replace if necessary. Check and reinstall if necessary.

Code: C6050

Description: Abnormally low fixing unit thermistor temperature • The fixing temperature remains below 120C/248F for 10 s.
Causes: Poor contact in the fixing unit thermistor connector terminals. Broken fixing unit thermistor wire. Fixing unit thermistor installed incorrectly. Fixing unit thermostat triggered. Fixing heater M and S installed incorrectly. Broken fixing heater M and S wire.
Remedy: Check the connection of connector CN25 on the engine PCB and the continuity across the connector terminals. Repair or replace if necessary. Measure the resistance. If it is ∞Ω, replace the fixing unit thermistor. Check and reinstall if necessary. Check for continuity. If none, replace the fixing unit thermostat. Check and reinstall if necessary. Check for continuity. If none, replace the fixing heater M and S.

Code: C6400

Description: Zero-crossing signal problem • The main PCB does not detect the zero-crossing signal (Z CROSS SIG) for the time specified below. At power-on: 3 s Others: 5 s
Causes: Poor contact in the connector terminals. Defective power source PCB. Defective main PCB.
Remedy: Check the connection of connectors CN17 on the main PCB and CN2 on the power source PCB, and the continuity across the connector terminals. Repair or replace if necessary. Check if the zero-crossing signal is output from CN2-7 on the power source PCB. If not, replace the power source PCB. Replace the main PCB if C6400 is detected while CN2-7 on the power source PCB outputs the zero-crossing signal.

Code: C7100

Description: Toner sensor problem • The toner sensor output voltage is outside the range of 0.5 to 4.5 V during copying or in maintenance item U130. • The toner sensor control voltage cannot be set within the range in maintenance item U130
Causes: Defective toner sensor. Poor contact in the toner sensor connector terminals. Defective developer.
Remedy: Replace the toner sensor. Reinsert the connector. Also check for continuity within the connector cable. If none, remedy or replace the cable. Replace the developer.

Code: C7300

Description: Toner hopper problem • Toner level is not detected when toner empty is detected.
Causes: Defective toner level detection sensor. Poor contact in the toner level detection sensor connector terminals.
Remedy: Replace the toner level detection sensor. Reinsert the connector. Also check for continuity within the connector cable. If none, remedy or replace the cable.
Đăng ký nhận bản tin Đăng ký nhận bản tin Đăng ký nhận bản tin Đăng ký nhận bản tin
Đăng ký nhận bản tin
Nhận ưu đãi sớm nhất khi chương trình diễn ra

Đăng ký nhận bản tin

Việc cho phép sử dụng cookie sẽ giúp cải thiện trải nghiệm của bạn trên trang web này. Chính sách cookie