Thương hiệu phân phối chính hãng
Giỏ hàng

Mã lỗi Kyocera TASKalfa 180 — Trang 4/4

Code: C6000

Description: Fuser heater break
The temperature does not reach 70 °C/ 158°F in 15 s before secondary stabilization.
Temperature rise of 1°C/1.8°F does not occur in 5 s before secondary stabilization (except during printing).
Causes: Poor contact in the fuser thermistor connector terminals.
Fuser thermistor installed incorrectly.
Fuser thermostat triggered.
Fuser heater installed incorrectly.
Broken fuser heater wire.
Remedy: Poor contact in the fuser thermistor connector terminals. Reinsert the connector. Also check for continuity within the connector cable. If none, remedy or replace the cable.
Fuser thermistor installed incorrectly. Check and reinstall if necessary.
Fuser thermostat triggered. Check for continuity. If none, replace the fuser thermostat.
Fuser heater installed incorrectly. Check and reinstall if necessary.
Broken fuser heater wire. Check for continuity. If none, replace the fuser heater.

Code: C6020

Description: Abnormally high fuser thermistor temperature
Fuser thermistor is detected 230°C/ 446°F or more for 40 ms.
Causes: Shorted thermistor.
Broken heater control circuit on the power source PWB
Remedy: Shorted thermistor. Measure the resistance. If it is 0Ω, replace the thermistor.
Broken heater control circuit on the power source PWB. Replace the power source PWB and check for correct operation.

Code: C6050

Description: Abnormally low fuser thermistor temperature
Fuser thermistor remains below 90°C/ 194°F for 1 s.
Causes: Poor contact in the fuser thermistor connector terminals.
Broken fuser thermistor wire.
Fuser thermistor installed incorrectly.
Fuser thermostat triggered.
Fuser heater installed incorrectly.
Broken fuser heater wire.
Remedy: Poor contact in the fuser thermistor connector terminals. Reinsert the connector. Also check for continuity within the connector cable. If none, remedy or replace the cable.
Broken fuser thermistor wire. Measure the resistance. If it is ∞, replace the fixing thermistor.
Fuser thermistor installed incorrectly. Check and reinstall if necessary.
Fuser thermostat triggered. Check for continuity. If none, replace the fuser thermostat.
Fuser heater installed incorrectly. Check and reinstall if necessary.
Broken fuser heater wire. Check for continuity. If none, replace the fuser heater.

Code: C6400

Description: Zero-cross signal error
Interrupt of the zero-cross signal does not occur more than 1 s.
Causes: Poor contact in the connector terminals
Defective power source PWB.
Defective main/ engine PWB.
Remedy: Poor contact in the connector terminals. Reinsert the connector. Also check for continuity within the connector cable. If none, remedy or replace the cable.
Defective power source PWB. Check if the zero-crossing signal is output from YC2-2 on the power source PWB. If not, replace the power source PWB.
Defective main/ engine PWB. Replace the main/engine PWB if C6400 is detected while YC2-2 on the power source PWB outputs the zero-crossing signal.

Code: C7800

Description: Broken external thermistor wire
The thermistor output value is 0.5 V or less.
Causes: Poor contact in the connector terminals.
Defective humidity sensor.
Remedy: Poor contact in the connector terminals. Reinsert the connector. Also check for continuity within the connector cable. If none, remedy or replace the cable.
Defective humidity sensor. Replace the cassette PWB and check for correct operation.

Code: C7810

Description: Short-circuited external thermistor wire
The thermistor output value is 4.5 V or more.
Causes: Poor contact in the connector terminals.
Defective humidity sensor.
Remedy: Poor contact in the connector terminals. Reinsert the connector. Also check for continuity within the connector cable. If none, remedy or replace the cable.
Defective humidity sensor. Replace the cassette PWB and check for correct operation.
Đăng ký nhận bản tin Đăng ký nhận bản tin Đăng ký nhận bản tin Đăng ký nhận bản tin
Đăng ký nhận bản tin
Nhận ưu đãi sớm nhất khi chương trình diễn ra

Đăng ký nhận bản tin

Việc cho phép sử dụng cookie sẽ giúp cải thiện trải nghiệm của bạn trên trang web này. Chính sách cookie