Thương hiệu phân phối chính hãng
Giỏ hàng

Mã lỗi Kyocera TASKalfa 3010i — Trang 8/16

Code: 6230

Description: Broken fuser edge thermistor wire
A/D value of the fuser thermistor 1 exceeds 251 bit continuously for 5.6 s during warming up
Causes: Fuser unit1. Fuser thermistor 1. Engine PWB.
Remedy: Fuser unit 1. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. Fuser thermistor 1 and Fuser PWB (YC2) Fuser PWB and Engine PWB (YC22) 2. If the wiring is disconnected, shorted or grounded, replace the wiring. 3. If the I/F connector pins of the fuser unit and the main unit are deformed owing to foreign matters, such as paper dusts, replace the connectors or the units including the connectors.
Fuser thermistor 1 Replace the Fuser unit.
Engine PWB 1. Check the engine software and upgrade to the latest, if necessary. 2. Replace the engine PWB.

Code: 6250

Description: Abnormally low fuser edge thermistor temperature
When the detection temperature of the fixing thermistor 1 is falling target temperature by 75 °C or more for 1 second after secondary stable temperature attainment.
Causes: Fuser unit. Fuser thermostat. Fuser heater. Engine PWB.
Remedy: Fuser unit 1. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. Fuser thermistor 1 and Fuser PWB (YC2) Fuser PWB and Engine PWB (YC22) 2. If the wiring is disconnected, shorted or grounded, replace the wiring. 3. If the I/F connector pins of the fuser unit and the main unit are deformed owing to foreign matters, such as paper dusts, replace the connectors or the units including the connectors.
Fuser thermostat Fuser heater. Replace the Fuser unit.
Engine PWB 1. Check the engine software and upgrade to the latest, if necessary. 2. Replace the engine PWB.

Code: 6400

Description: Zero-cross signal error
While fuser heater ON/OFF control is performed, the zerocross signal is not input within 3 s.
Causes: Fuser unit.
Remedy: 1. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. Power source PWB (YC6) and engine PWB (YC24) 2. If the wiring is disconnected, shorted or grounded, replace the wiring. 3. Replace the fuser heater PWB.

Code: 6910

Description: Engine software ready error
The device won’t engage in ready state in 60 minutes after warming-up has began. (A previous timeout process has not been cancelled.)
Causes: Engine PWB.
Remedy: 1. Turn the main power switch off and after 5 seconds, turn it on. 2. Reinstall the engine software. 3. Replace the engine PWB.

Code: 7200

Description: Broken outer temperature sensor 2 wire
The sensor input sampling is greater than 244.
Causes: BD PWB. Engine PWB.
Remedy: BD PWB 1. Confirm External Temp is displayed by U139 temperature and humidity. 2. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. BD PWB and APC PWB (YC2) APC PWB (YC1) and Engine PWB (YC27) 3. If the wiring is disconnected, shorted or grounded, replace the wiring. 4. Replace the BD PWB.
Engine PWB 1. Check the engine software and upgrade to the latest, if necessary. 2. Replace the engine PWB.

Code: 7210

Description: Short-circuited outer temperature sensor
The temperature sensor input sampling is less than 10.
Causes: BD PWB. Engine PWB.
Remedy: BD PWB 1. Confirm External Temp is displayed by U139 temperature and humidity. 2. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. BD PWB and APC PWB (YC2) APC PWB (YC1) and Engine PWB (YC27) 3. If the wiring is disconnected, shorted or grounded, replace the wiring. 4. Replace the BD PWB.
Engine PWB 1. Check the engine software and upgrade to the latest, if necessary. 2. Replace the engine PWB.

Code: 7800

Description: Broken outer temperature sensor wire
The temperature sensor input sampling is more than 237F
Causes: Thermistor PWB. Engine PWB.
Remedy: Thermistor PWB 1. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. Thermistor PWB and Engine PWB (YC6) 2. If the wiring is disconnected, shorted or grounded, replace the wiring. 3. Replace the thermistor PWB
Engine PWB 1. Check the engine software and upgrade to the latest, if necessary. 2. Replace the engine PWB.

Code: 7810

Description: Short-circuited external thermistor wire external thermistor delivers 3V or more.
Causes: Thermistor PWB. Engine PWB.
Remedy: Thermistor PWB 1. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. Thermistor PWB and Engine PWB (YC6) 2. If the wiring is disconnected, shorted or grounded, replace the wiring. 3. Replace the thermistor PWB.
Engine PWB 1. Check the engine software and upgrade to the latest, if necessary. 2. Replace the engine PWB.
Đăng ký nhận bản tin Đăng ký nhận bản tin Đăng ký nhận bản tin Đăng ký nhận bản tin
Đăng ký nhận bản tin
Nhận ưu đãi sớm nhất khi chương trình diễn ra

Đăng ký nhận bản tin

Việc cho phép sử dụng cookie sẽ giúp cải thiện trải nghiệm của bạn trên trang web này. Chính sách cookie