Thương hiệu phân phối chính hãng
Giỏ hàng

Mã lỗi Kyocera TASKalfa 520i — Trang 6/13

Code: C4000

Description: Polygon motor synchronization problem
The polygon motor does not reach the stable speed within 20 s of the START signal turning on.
Causes: Poor contact in the connector terminals.
Defective polygon motor.
Defective engine PWB.
Remedy: Poor contact in the connector terminals. Check the connection of connector YC3 on the engine PWB and laser scanner unit, and the continuity across the connector terminals. Repair or replace if necessary.
Defective polygon motor. Replace the laser scanner unit.
Defective engine PWB. Replace the engine PWB and check for correct operation.

Code: C4010

Description: Polygon motor steady-state problem
Stable OFF is detected for 20 s continuously after polygon motor stability.
Causes: Poor contact in the connector terminals.
Defective polygon motor.
Defective engine PWB.
Remedy: Poor contact in the connector terminals. Check the connection of connector YC3 on the engine PWB and laser scanner unit, and the continuity across the connector terminals. Repair or replace if necessary.
Defective polygon motor. Replace the laser scanner unit.
Defective engine PWB. Replace the engine PWB and check for correct operation.

Code: C4100

Description: BD initialization problem
5 consecutive BD errors were detected during an 800 ms interval after the polygon motor stabilized.
Causes: Poor contact in the connector terminals.
Defective polygon motor.
Defective engine PWB.
Remedy: Poor contact in the connector terminals. Check the connection of connector YC3 on the engine PWB and laser scanner unit, and the continuity across the connector terminals. Repair or replace if necessary.
Defective polygon motor. Replace the laser scanner unit.
Defective engine PWB. Replace the engine PWB and check for correct operation.

Code: C6000

Description: Fuser heater break
Fuser thermistor 1 detected less than 70°C/158°F for 10 s during warm-up and ready in. During warm-up, the temperature at the fuser unit thermistor 1 does not rise by 1°C/1.8°F continuously for 5 s. Fuser thermistor 2 detected less than 40°C/104°F for 10 s during warm-up and ready in. During warm-up, the temperature at the fuser unit thermistor 2 does not rise by 1°C/1.8°F continuously for 5 s.
Causes: Defective fuser heater 1 or 2.
Installation defectiveness on fuser thermistor 1.
Defective fuser thermostat.
Defective PWB.
Remedy: Defective fuser heater 1 or 2. Replace the fuser heater 1 or 2.
Installation defectiveness on fuser thermistor 1. Check the mounting state of the fuser thermistor 1. If any problem is found, repair it.
Defective fuser thermostat. Replace the fuser thermostat.
Defective PWB. Replace the power source PWB or engine PWB and check for correct operation.

Code: C6020

Description: Abnormally high fuser thermistor temperature
Fuser thermistor 1 or 2 is detected 250°C/482°F or more for 40 ms.
Causes: Installation defectiveness on fuser thermistor 1 or 2.
Defective fuser thermistor unit 1 or 2.
Defective engine PWB.
Remedy: Installation defectiveness on fuser thermistor 1 or 2. Check the mounting state of the fuser thermistor 1 or 2. If any problem is found, repair it.
Defective fuser thermistor unit 1 or 2. Replace the fuser thermistor 1 or 2.
Defective engine PWB. Replace the engine PWB and check for correct operation.

Code: C6030

Description: Fuser thermistor break error
The fuser thermistor break signal is detected continuously for 1 s.
Causes: Installation defectiveness on fuser thermistor 1 or 2.
Defective fuser thermistor 1 or 2.
Defective engine PWB.
Remedy: Installation defectiveness on fuser thermistor 1 or 2. Check the mounting state of the fuser thermistor 1 or 2. If any problem is found, repair it.
Defective fuser thermistor 1 or 2. Replace the fuser thermistor 1 or 2.
Defective engine PWB. Replace the engine PWB and check for correct operation.

Code: C6040

Description: Fuser thermistor 1 detection error
Fuser thermistor 1 detected an abnormal value for at least 1 s.
Causes: Installation defectiveness on fuser thermistor 1.
Defective fuser thermistor 1.
Defective engine PWB.
Remedy: Installation defectiveness on fuser thermistor 1. Check the mounting state of the fuser thermistor 1. If any problem is found, repair it.
Defective fuser thermistor 1. Replace the fuser thermistor 1.
Defective engine PWB. Replace the engine PWB and check for correct operation.

Code: C6050

Description: Abnormally low fuser thermistor temperature
Fuser thermistor 1 is detected 80°C/ 176°F less than 1 s continuously during copying.
Causes: Defective fuser heater 1 or 2.
Installation defectiveness on fuser thermistor 1.
Defective PWB.
Remedy: Defective fuser heater 1 or 2. Replace the fuser heater 1 or 2.
Installation defectiveness on fuser thermistor 1. Check the mounting state of the fuser thermistor 1. If any problem is found, repair it.
Defective PWB. Replace the power source PWB or engine PWB and check for correct operation.
Đăng ký nhận bản tin Đăng ký nhận bản tin Đăng ký nhận bản tin Đăng ký nhận bản tin
Đăng ký nhận bản tin
Nhận ưu đãi sớm nhất khi chương trình diễn ra

Đăng ký nhận bản tin

Việc cho phép sử dụng cookie sẽ giúp cải thiện trải nghiệm của bạn trên trang web này. Chính sách cookie