Thương hiệu phân phối chính hãng
Giỏ hàng

Mã lỗi Kyocera TASKalfa 8000i — Trang 10/23

Code: 6120

Description: Abnormally high fuser thermistor 5 temperature
Fuser thermistor 5 detects a temperature higher than 190C/374F for 1 s.
Causes: Deformed connector pin.
Defective triac.
Shorted fuser thermistor 5.
Defective engine PWB.
Remedy: Shorted fuser thermistor 5. Replace the fuser unit.
Defective engine PWB. Replace the engine PWB and check for correct operation.

Code: 6130

Description: Broken fuser thermistor 5 wire
Input from fuser thermistor 5 is 992 or more (A/D value) continuously for 60 s.
Causes: Defective connector cable or poor contact in the connector.
Deformed connector pin.
Defective triac.
Broken fuser thermistor 5 wire.
Defective fuser IH.
Defective engine PWB.
Remedy: Defective connector cable or poor contact in the connector. Reinsert the connector. Also check for continuity within the connector cable. If none, replace the cable. Fuser unit and engine PWB (YC26)
Broken fuser thermistor 5 wire. Replace the fuser unit.
Defective fuser IH. Replace the fuser unit.
Defective engine PWB. Replace the engine PWB and check for correct operation.

Code: 6150

Description: Abnormally low fuser thermistor 5 temperature
Fuser thermistor 5 detects a temperature lower than 30C/ 86F for 1 s after warming up.
Causes: Deformed connector pin.
Defective triac.
Defective fuser thermistor 5.
Defective fuser IH.
Defective engine PWB.
Remedy: Defective fuser thermistor 5. Replace the fuser unit.
Defective fuser IH. Replace the fuser unit.
Defective engine PWB. Replace the engine PWB and check for correct operation.

Code: 6200

Description: Broken fuser edge heater wire
Fuser thermistor 2 does not reach 100° C/212 °F even after 60 s during warming up. The detected temperature of fuser thermistor 2 does not reach the specified temperature (ready indication temperature) for 420 s in warming up after reached to 100° C/212 °F.
Causes: Defective connector cable or poor contact in the connector.
Deformed connector pin.
Defective triac.
Fuser thermostat triggered.
Defective fuser IH.
Defective engine PWB.
Remedy: Defective connector cable or poor contact in the connector. Reinsert the connector. Also check for continuity within the connector cable. If none, replace the cable. Power source PWB (YC3) and fuser IH PWB (YC1) Fuser IH PWB (YC4) and engine PWB (YC26)
Fuser thermostat triggered. Replace the fuser unit.
Defective fuser IH. Replace the fuser unit.
Defective engine PWB. Replace the engine PWB and check for correct operation.

Code: 6220

Description: Abnormally high fuser thermistor 2 temperature
Fuser thermistor 2 detects a temperature higher than 240C/464F for 1 s.
Causes: Deformed connector pin.
Defective triac.
Shorted fuser thermistor 2.
Defective engine PWB.
Remedy: Shorted fuser thermistor 2. Replace the fuser unit.
Defective engine PWB. Replace the engine PWB and check for correct operation.

Code: 6230

Description: Broken fuser thermistor 2 wire
The Input signal from the fuser thermistor 2 is 992 or more (A/D) continuously for 1 second during the temperature detected by the fuser thermistor 1 is 100 deg-C or more.
Causes: Defective connector cable or poor contact in the connector.
Deformed connector pin.
Defective triac.
Broken fuser thermistor 2 wire.
Fuser thermostat triggered.
Defective fuser IH.
Defective engine PWB.
Remedy: Defective connector cable or poor contact in the connector. Reinsert the connector. Also check for continuity within the connector cable. If none, replace the cable. Fuser unit and engine PWB (YC26)
Broken fuser thermistor 2 wire. Replace the fuser unit.
Fuser thermostat triggered. Replace the fuser unit.
Defective fuser IH. Replace the fuser unit.
Defective engine PWB. Replace the engine PWB and check for correct operation.

Code: 6250

Description: Abnormally low fuser thermistor 2 temperature
Fuser thermistor 2 detects a temperature lower than 100C/212F for 1 s during ready or print.
Causes: Deformed connector pin.
Defective triac.
Defective fuser thermistor 2.
Defective fuser IH.
Defective engine PWB.
Remedy: Defective fuser thermistor 2. Replace the fuser unit.
Defective fuser IH. Replace the fuser unit.
Defective engine PWB. Replace the engine PWB and check for correct operation.

Code: 6320

Description: Abnormally high fuser thermistor 3 temperature
Fuser thermistor 3 detects a temperature higher than 215C/419F for 1 s.
Causes: Deformed connector pin.
Defective triac.
Shorted fuser thermistor 3.
Defective engine PWB.
Remedy: Shorted fuser thermistor 3. Replace the fuser unit.
Defective engine PWB. Replace the engine PWB and check for correct operation.
Đăng ký nhận bản tin Đăng ký nhận bản tin Đăng ký nhận bản tin Đăng ký nhận bản tin
Đăng ký nhận bản tin
Nhận ưu đãi sớm nhất khi chương trình diễn ra

Đăng ký nhận bản tin

Việc cho phép sử dụng cookie sẽ giúp cải thiện trải nghiệm của bạn trên trang web này. Chính sách cookie