Thương hiệu phân phối chính hãng
Giỏ hàng

Mã lỗi Lexmark MS610dte — Trang 8/10

Code: 948.xx

Description: Failed engine card—pel clock check failed.
Remedy: Replace the controller board

Code: 950.xx

Description: NVRAM mismatch failure—mismatch between controller board EEPROM and control panel mirror. ".xx" codes: • 00-29— mismatch between system and mirror • 30-60—mismatch between secure and system
Remedy: Warning—Potential Damage: When replacing any of the following components: • Control panel assembly • Controller board assembly Replace only one component at a time. Replace the required component and perform a POR before replacing a second component listed above. If this procedure is not followed, the printer will be rendered inoperable. Never replace two or more of the components listed above without a POR after installing each one or the printer will be rendered inoperable. Never install and remove components listed above as a method of troubleshooting components. Once a component has been installed in a machine, it can not be used in another machine. It must be returned to the manufacturer.
Step 1 Check the control panel assembly. Was the control panel assembly recently replaced? Go to step 3. Go to step 2.
Step 2 Check the controller board assembly. Was the controller board assembly recently replaced? Go to step 4. Contact next level of support.
Step 3 Replace the current control panel assembly with the control panel assembly. Go to “Control panel assembly removals”. Does the error remain? Go to step 5. The problem is solved.
Step 4 Replace the current controller board assembly with the original controller board assembly. Go to “Controller board removals”. Does the problem continue? Go to step 6. The problem is solved.
Step 5 Replace the original control panel assembly with a new and not previously installed control panel assembly. Does the error continue? Contact the next level of support. The problem is solved
Step 6 Replace the original control panel assembly with a new and not previously installed control panel door assembly. Does the error continue? Contact the next level of support. The problem is solved.

Code: 952.xx

Description: Service NVRAM Failure A recoverable MVRAM Cyclic Redundancy Check (CRC) error occurred. n is the offset at which the error occurred.
Remedy: Performing a POR will clear this error.

Code: 953.xx

Description: Service NVRAM Failure NVRAM chip failure with mirror.
Remedy: Replace the controller board.

Code: 954.xx

Description: Service NVRAM Failure The NVRAM chip failure with controller part.
Remedy: • POR the printer. • If the problem persists, then replace the controller board.

Code: 955.xx

Description: Service Code CRC <loc> The Code ROM or NAND flash failed the Cyclic Redundancy Check (CRC) check or the NAND experienced an uncorrectable multi-bit failure. <loc> indicates the source of the failure and has one of the following values: • CRC Failure: The source is a failing package indicated by Pn where n is the package number. This error could occur on a controller with ROM or NAND flash and could occur as a result of the CRC check done when the machine is powered on. The range of package numbers is from 0 to 15. • Error Correction Code (ECC) Failure: The source is a failing page indicated by Bn where “n” is the page number. This error occurs only if a multi-bit failure is detected during the ECC execution. Single bit failures will be corrected automatically and will not result in a service error. The range of page numbers is from 0 to 1023.
Remedy: • POR the printer. • If the problem persists, then replace the controller board.

Code: 956.xx

Description: Service Controller Board Controller board failure. Processor failure. Check on .02 for fan error.
Remedy: • POR the printer. • If the problem persists, then replace the controller board.

Code: 957.xx

Description: Service Controller Board Controller board failure. ASIC failure.
Remedy: • POR the printer. • If the problem persists, then replace the controller board.
Đăng ký nhận bản tin Đăng ký nhận bản tin Đăng ký nhận bản tin Đăng ký nhận bản tin
Đăng ký nhận bản tin
Nhận ưu đãi sớm nhất khi chương trình diễn ra

Đăng ký nhận bản tin

Việc cho phép sử dụng cookie sẽ giúp cải thiện trải nghiệm của bạn trên trang web này. Chính sách cookie