Thương hiệu phân phối chính hãng
Giỏ hàng

Mã lỗi Lexmark MX911dte — Trang 6/10

Code: 31, 32

Description: 31 A supply.related error was detected: . The cartridge is missing or undetected. . The photoconductor is missing or undetected. . The cartridge is defective. . The photoconductor is defective. 32 The cartridge or photoconductor is unsupported.
Remedy: Step 1 a Make sure that the cartridge or photoconductor is installed. b Check if the cartridge or photoconductor is supported, and replace if necessary. Does the problem remain? Go to step 2. The problem is solved.

Code: 34

Description: Paper size mismatch was detected.
Remedy: Step 1 a Make sure that the tray paper length and tray paper width guides are properly installed. b Check the guides for wear or damage, and replace if necessary. Does the problem remain? Go to step 2. The problem is solved. Step 2 Check the paper width and paper length sensor actuators for damage, and replace if necessary. Does the problem remain? Go to step 3. The problem is solved. Step 3 a Reseat the paper width and paper length sensor cables. b Check the cables for damage, and replace if necessary. Does the problem remain? Go to step 4. The problem is solved. Step 4 Check the paper width and paper length sensors for damage, and replace if necessary. Does the problem remain? Go to step 5. The problem is solved.

Code: 35, 37, 38

Description: 35 The printer memory is insufficient to enable Resource Save. 37 The printer memory was insufficient to do the job. 38 Memory is full.
Remedy: Step 1 Reset the printer, and then navigate to: Paper Menu > Print Settings > Download Target > Disk Does the problem remain? Go to step 2. The problem is solved. Step 2 If applicable, install extra memory card. If applicable, make sure that the additional memory card is properly installed. Does the problem remain? Go to step 3. The problem is solved. Step 3 Check the controller board pins for damage, and replace if necessary. See “Controller board removal”. Does the problem remain? Contact the next level of support. The problem is solved.

Code: 39

Description: The page is too complex to print.
Remedy: Step 1 Reset the printer, and then navigate to: Paper Menu > Print Settings > Download Target > Disk Does the problem remain? Go to step 2. The problem is solved. Step 2 Enter the Diagnostics menu, and then navigate to: PRINTER TESTS > Tray 1 > Single Does the problem remain? Go to step 4. Go to step 3.

Code: 42

Description: The cartridge is incompatible due to printer region mismatch.
Remedy: Step 1 a Make sure that the cartridge or photoconductor is installed. b Check if the cartridge or photoconductor is supported, and replace if necessary. Does the problem remain? Go to step 2. The problem is solved.

Code: 50

Description: PPDS encountered a font error.
Remedy: Step 1 Navigate to Settings > PPDS Menu > Best Fit. Make sure that the value is set to On. Does the problem remain? Go to step 2. The problem is solved. Step 2 Make sure that the font is supported by the memory card. Replace the memory card if necessary. Does the problem remain? Go to step 3. The problem is solved. Step 3 Check the controller board pins for damage, and replace if necessary. See “Controller board removal”. Does the problem remain? Contact the next level of support. The problem is solved.

Code: 51

Description: The flash memory is defective.
Remedy: Step 1 Navigate to Settings > Print settings > Job Accounting Menu Settings > Log Near Full Level. Make sure that the value is set to maximum. Does the problem remain? Go to step 2. The problem is solved. Step 2 If applicable, make sure that the optional memory card is supported. Does the problem remain? Go to step 3. The problem is solved.

Code: 52

Description: The flash memory is insufficient.
Remedy: Step 1 Navigate to Settings > Print settings > Utilities Menu > Format Flash > Yes. Does the problem remain? Go to step 3. Go to step 2. Step 2 Navigate to Settings > Print settings > Job Accounting Menu Settings > Log Near Full Level. Make sure that the value is set to maximum. Does the problem remain? Go to step 3. The problem is solved. Step 3 If applicable, make sure that the optional memory card is supported. Does the problem remain? Go to step 4. The problem is solved. Step 4 Check the controller board pins for damage, and replace if necessary. See “Controller board removal”. Does the problem remain? Go to step 5. The problem is solved. Step 5 Make sure that the firmware version is the latest, and update if necessary. Does the problem remain? Contact the next level of support. The problem is solved.
Đăng ký nhận bản tin Đăng ký nhận bản tin Đăng ký nhận bản tin Đăng ký nhận bản tin
Đăng ký nhận bản tin
Nhận ưu đãi sớm nhất khi chương trình diễn ra

Đăng ký nhận bản tin

Việc cho phép sử dụng cookie sẽ giúp cải thiện trải nghiệm của bạn trên trang web này. Chính sách cookie