Thương hiệu phân phối chính hãng
Giỏ hàng

Mã lỗi OKI C931dn — Trang 4/8

Code: 114

Display: Service Call 114:Error
Description: A 4th Tray for another model was detected.
Remedy: Is a 4th Tray provided for this model installed? Yes Install a correct 4th Tray.

Code: 115

Display: Service Call 115:Error
Description: A 5th Tray for another model was detected.
Remedy: Is a 5th Tray provided for this model installed? Yes Install a correct 5th Tray.

Code: 121

Display: Service Call 121:Error
Description: High voltage power supply interface error
Remedy: Is the fuse on the printer control PCB blown? Yes Replace the printer control PCB (then check the following).
Is the cable connecting the printer control PCB to the high voltage power supply unit connected properly? No Re-connect it properly. Yes Check for defective contact points of the high voltage system.
Is there any defective contact point? No Replace the high voltage power supply unit.

Code: 123

Display: Service Call 123:Error
Description: Abnormal environment humidity or unconnected humidity sensor
Remedy: Power OFF/ON. Does this error recur? Yes Replace the environmental sensor board and the FFC.
Does this error recur? Yes Replace the printer control PCB.

Code: 124

Display: Service Call 124:Error
Description: Abnormal environment humidity
Remedy: Power OFF/ON. Does this error recur? Yes Replace the environmental sensor board and the FFC.
Does this error recur? Yes Replace the printer control PCB.

Code: 125

Display: Service Call 125:Error
Description: Multi-purpose Tray Home Error
Remedy: Does the motor un in the motor testing of the PU self-diagnostic mode. Yes Check the sensor cable for a break or short, and the connector semilocking relay PCB and the printer control PCB for abnormal condition. No Check the hopping motor and the gear train for abnormal condition.

Code: 126

Display: Power Off and Wait for a while 126:Condensing Error
Description: Dew condensation in the printer was detected.
Remedy: This error tends to occur after a printer is carried in from the outsides. Leave the printer for 2 hours to half a day at room temperature, and turn on the power. After leaving the printer at room temperature, turn on the power again. Does this error recur? Yes Replace the environmental sensor board and the FFC. Does this error recur? Yes Replace the printer control PCB.

Code: 128

Display: Service Call 128:Error
Description: 01: Fuser Exhaust Fan 1 02: Low Voltage Fan 03: PU Fan 05: Station 1 ID Intake Fan 09: Second Transfer Adsorption Fan 0A: Fuser Intake Fan 0B: Station 2 ID Intake Fan 0C: Duplex Fan 0D: Fuser Exhaust Fun 2 0E: Station 3 ID Intake Fan 0F: Station 4 ID Intake Fan 10: Station 5 ID Intake Fan
Remedy: Is the cable to respective fans connected properly? No Re-connect the fan properly. Yes Replace the fan motor. Does this error recur? No Replace the applicable PCB. 01: Driver relay PCB 02: Printer control PCB 03: Printer control PCB 05: Driver relay PCB 09: Rail unit relay PCB 0A: Driver relay PCB 0B: Driver relay PCB 0C: Duplex unit PCB 0D: Driver relay PCB 0E: Driver relay PCB 0F: Driver relay PCB 10: Driver relay PCB
Đăng ký nhận bản tin Đăng ký nhận bản tin Đăng ký nhận bản tin Đăng ký nhận bản tin
Đăng ký nhận bản tin
Nhận ưu đãi sớm nhất khi chương trình diễn ra

Đăng ký nhận bản tin

Việc cho phép sử dụng cookie sẽ giúp cải thiện trải nghiệm của bạn trên trang web này. Chính sách cookie