Thương hiệu phân phối chính hãng
Giỏ hàng

Mã lỗi Ricoh Aficio 1055 — Trang 5/18

Code: SC337

Description: Polygonal mirror motor error 3
The XSCRDY signal becomes high while the polygonal mirror motor turns on, even though there was no demand for either turning off the motor or changing the motor speed.
Causes: • Poor cable connection to the polygonal mirror motor driver. • Polygonal mirror motor (driver) defective • BICU defective

Code: SC338

Description: Polygonal mirror motor error 1
The XSCRDY signal does not become stable within 20 seconds after the polygonal mirror motor turns on or off or the polygon motor speed is changed.
Causes: • Poor cable connection to the polygonal mirror motor driver. • Polygonal mirror motor (driver) defective • BICU defective

Code: SC340

Description: TD sensor output error
The TD sensor output voltage (Vt), which is measured during each copying process, is one of the following 10 times consecutively. 1) Vt = 0.5 volts or lower 2) Vt = 4.0 volts or higher
Causes: • TD sensor defective • Poor connection between the TD sensor and the I/O board. • I/O board defective NOTE: In this error condition, the toner supply is controlled using pixel count and Vsp/Vsg.

Code: SC341

Description: TD sensor adjustment error 1
During the TD sensor auto adjustment, the TD sensor output voltage (Vt) is 2.5 volts or higher even though the control voltage is set to the minimum value (PWM = 0)
Causes: • TD sensor defective • Poor connection between the TD sensor and the I/O board. • I/O board defective NOTE: In this error condition, the toner supply is controlled using pixel count and Vsp/Vsg.

Code: SC342

Description: TD sensor adjustment error 2
During the TD sensor auto adjustment, the TD sensor output voltage (Vt) does not come in the target range (2.5 ± 0.1V) within 20 seconds.
Causes: • TD sensor defective • Poor connection between the TD sensor and the I/O board. • I/O board defective NOTE: In this error condition, the toner supply is controlled using pixel count and Vsp/Vsg.

Code: SC345

Description: Development bias leak
A development bias leak signal is detected.
Causes: • Poor connection between the development bias terminal and the development P.P. • Development P.P. defective

Code: SC350

Description: ID sensor error 1
One of the following ID sensor output voltages was detected twice consecutively when checking the ID sensor pattern. 1) Vsp ≥ 2.5V 2) Vsp = 0V
Causes: • ID sensor defective • ID sensor connector defective • Poor ID sensor connector connection • I/O board (IOB) defective • Charge or development power pack defective • Dirty ID sensor • Defect at ID sensor pattern writing area of the drum

Code: SC351

Description: ID sensor error 2
One of the following ID sensor output voltages was detected twice consecutively when checking the ID sensor pattern. 1) Vsg< 2.5V 2) Vsg = 0V 3) The ID sensor output voltage is 5.0V and the PWM signal input to the ID sensor is 0 when checking the ID sensor pattern
Causes: • ID sensor defective • ID sensor connector defective • Poor ID sensor connector connection • I/O board (IOB) defective • Charge or development power pack defective • Dirty ID sensor • Defect at the ID sensor pattern writing area of the drum
Đăng ký nhận bản tin Đăng ký nhận bản tin Đăng ký nhận bản tin Đăng ký nhận bản tin
Đăng ký nhận bản tin
Nhận ưu đãi sớm nhất khi chương trình diễn ra

Đăng ký nhận bản tin

Việc cho phép sử dụng cookie sẽ giúp cải thiện trải nghiệm của bạn trên trang web này. Chính sách cookie