Thương hiệu phân phối chính hãng
Giỏ hàng

Mã lỗi Ricoh Aficio 1060 — Trang 7/25

Code: 441

Description: Development motor lock
The development motor lock signal remains high for 2 seconds while the development motor is on.
Causes: • Drive mechanism overloaded due to toner clumping in the wasted toner path
• Motor driver board defective

Code: 490

Description: Main fan error
The main fan motor lock signal goes high for 5 s while the fan is on.
Causes: • Fan motor overloaded due to obstruction
• Fan connector disconnected

Code: 495

Description: Toner recycling unit error
Encoder pulse does not change for 3 s after the main motor switches on.
Causes: • Waste toner transport has stopped due to motor overload
• Toner end sensor detective, disconnected

Code: 496

Description: Toner collection bottle errorThe toner collection bottle set switch remains off when the front door is closed.
Causes: • No toner collection bottle set
• Poor connection of the switch connector

Code: 497

Description: Toner collection motor error
The toner collection motor connector set signal remains off for 1 s.
Causes: • Toner pump motor defective
• Motor connector loose, disconnected

Code: 501

Description: Tray 1 lift malfunction
• The lift sensor is not activated within 10 seconds after the tray lift motor starts lifting the bottom plate.
• When the tray lowers, the tray lift sensor does not go off within 1.5 sec.
• Tray overload detected when the tray is set.
• The lower limit sensor of the LCT does not detect the lower limit within 10 sec.
Causes: • Tray lift motor defective, disconnected
• Paper or other obstacle trapped between tray and motor
• Pick-up solenoid disconnected, blocked by an obstacle
• Too much paper loaded in tray Note (B246)
• At first, the machine displays a message asking the operator to reset the tray.
• This SC will not display until the operator has pulled the tray out and pushed it in 3 times.
• If the operator cycles the machine off/on before the 3rd opening and closing of the tray, the 3-count is reset.

Code: 502

Description: Tray 2 lift malfunction
• The lift sensor is not activated within 10 seconds after the tray lift motor starts lifting the bottom plate.
• When the tray lowers, the tray lift sensor does not go off within 1.5 sec.
• Tray overload detected when the tray is set.
Causes: • Tray lift motor defective or disconnected
• Paper or other obstacle trapped between tray and motor
• Pick-up solenoid disconnected or blocked by an obstacle
• Too much paper loaded in tray Note (B246)
• At first, the machine displays a message asking the operator to reset the tray.
• This SC will not display until the operator has pulled the tray out and pushed it in 3 times.
• If the operator cycles the machine off/on before the 3rd opening and closing of the tray, the 3-count is reset.

Code: 503

Description: Tray 3 lift malfunction
• The lift sensor is not activated within 10 seconds after the tray lift motor starts lifting the bottom plate.
• When the tray lowers, the tray lift sensor does not go off within 1.5 sec.
• Tray overload detected when the tray is set.
Causes: • Tray lift motor defective or disconnected
• Paper or other obstacle trapped between tray and motor
• Pick-up solenoid disconnected or blocked by an obstacle
• Too much paper loaded in tray Note (B246)
• At first, the machine displays a message asking the operator to reset the tray.
• This SC will not display until the operator has pulled the tray out and pushed it in 3 times.
• If the operator cycles the machine off/on before the 3rd opening and closing of the tray, the 3-count is reset.
Đăng ký nhận bản tin Đăng ký nhận bản tin Đăng ký nhận bản tin Đăng ký nhận bản tin
Đăng ký nhận bản tin
Nhận ưu đãi sớm nhất khi chương trình diễn ra

Đăng ký nhận bản tin

Việc cho phép sử dụng cookie sẽ giúp cải thiện trải nghiệm của bạn trên trang web này. Chính sách cookie