Description: Paper transfer unit position error - Timing & Condition • The paper transfer home position sensor does not detect the paper transfer unit moving into the contact position or the release position at the correct time.
Causes: • Defective paper transfer positioning clutch • Defective I/O control board
Remedy: 1. Replace the paper transfer H.P. sensor. (Input Check: SP 5-803-11) 2. Replace the paper transfer positioning clutch. (Output Check: SP 5-804-23) 3. Replace the I/O control board. - Signals to Check - • H.P.: CN229-5 or TP286 on I/O control board
Description: Image transfer belt cleaning unit position error - Timing & Condition • The belt cleaning home position sensor does not detect the transfer belt cleaning unit moving into the contact position or the release position at the correct time.
Causes: • Dirty sensor • Defective sensor • Defective belt cleaning clutch • Defective I/O control board • Defective main control board
Remedy: 1. Pull out and re-insert the image transfer belt unit. 2. Clean the belt cleaning H.P. sensor if it is dirty. 3. Replace the sensor. (Input Check: 5-803-12) 4. Replace the belt cleaning clutch. (Output Check: SP 5- 804-36) 5. Replace the I/O control board. 6. Replace the main control board. - Signals to Check - • H.P.: CN202-2 or TP254 on I/O control board
Description: Temperature sensor error - Timing & Condition - The temperature sensor output is out of range (2.75V or greater or less than 0.25V).
Causes: • Poor connection of connector • Defective humidity sensor • Defective I/O control board • Defective main control board
Remedy: 1. Check that the connectors (CN236, 214 & CN302) are properly connected on the I/O control board and main control board. 2. Replace the humidity sensor. 3. Replace the I/O control board. 4. Replace the main control board. - Signals to Check - • Temperature: CN236-6, TP247, or CN214-A9 on I/O control board / CN302-A1 or TP223 on main control board
Description: Humidity sensor error - Timing & Condition - The humidity sensor output is out of range (2.75V or greater or less than 0.25V)
Causes: • Poor connection of connector • Defective humidity sensor • Defective I/O control board • Defective main control board
Remedy: 1. Check the connector is properly connected on the I/O board (CN236). 2. Replace the humidity sensor. 3. Replace the I/O control board. 4. Replace the main control board. - Signals to Check - • Humidity: CN236-3, TP222, or CN214-A8 on I/O control board / CN302-A2 or TP168 on main control board
Description: Fusing motor error - Timing & Condition - • The feedback signal from the motor is still out of range 1 second after the trigger signal is sent. • The feedback signal becomes out of range for 2 seconds while the trigger signal is on.
Causes: • Poor connection of connector • Defective fusing motor • Defective I/O control board • Defective main control board
Remedy: 1. Check if the connector (CN204) is properly connected on the I/O control board. 2. Replace the fusing motor. (Output check: SP 5-804- 05,-06,-07,-08) 3. Replace the I/O control board. 4. Replace the main control board. 5. Check if anything causes overload for the fusing unit drive. - Signals to Check - • Motor OK: CN204-7 on I/O control board
Description: 1st paper tray error - Timing & Condition - • The upper limit sensor does not turn on1.5 s after the tray bottom plate starts to go up.
Causes: • Defective upper limit sensor • Defective tray bottom plate • Defective I/O control board • Defective main control board
Remedy: 1. Check if the spring of pick-up solenoid comes off. 2. Check if the sensor cable is properly connected. 3. Clean or replace the sensor and replace it if necessary (Input Check: SP 5-803-14 to 17). 4. Replace the tray bottom lever if it is broken. 5. Pull out the paper tray and check if the tray lift motor works properly (Output Check: SP 5-804-75 to 82). 6. Replace the I/O control board. 7. Replace the main control board. - Signals to Check - • Limit sensor H.P.: CN226-2 or TP206 on I/O control board
Description: 2nd paper tray error - Timing & Condition - • The upper limit sensor does not turn on1.5 s after the tray bottom plate starts to go up.
Causes: • Defective upper limit sensor • Defective tray bottom plate • Defective I/O control board • Defective main control board
Remedy: 1. Check if the spring of pick-up solenoid comes off. 2. Check if the sensor cable is properly connected. 3. Clean or replace the sensor and replace it if necessary (Input Check: SP 5-803-14 to 17). 4. Replace the tray bottom lever if it is broken. 5. Pull out the paper tray and check if the tray lift motor works properly (Output Check: SP 5-804-75 to 82). 6. Replace the I/O control board. 7. Replace the main control board. - Signals to Check - • Limit sensor H.P.: CN226-2 or TP206 on I/O control board
Description: 3rd paper tray error - Timing & Condition - • The upper limit sensor does not turn on1.5 s after the tray bottom plate starts to go up.
Causes: • Defective upper limit sensor • Defective tray bottom plate • Defective I/O control board • Defective main control board
Remedy: 1. Check if the spring of pick-up solenoid comes off. 2. Check if the sensor cable is properly connected. 3. Clean or replace the sensor and replace it if necessary (Input Check: SP 5-803-14 to 17). 4. Replace the tray bottom lever if it is broken. 5. Pull out the paper tray and check if the tray lift motor works properly (Output Check: SP 5-804-75 to 82). 6. Replace the I/O control board. 7. Replace the main control board. - Signals to Check - • Limit sensor H.P.: CN226-2 or TP206 on I/O control board
Nhận ưu đãi sớm nhất khi chương trình diễn ra
Đăng ký nhận bản tin
Việc cho phép sử dụng cookie sẽ giúp cải thiện trải nghiệm của bạn trên trang web này.
Chính sách cookie
Những cookie này là cần thiết để trang web hoạt động đúng cách.
Những cookie này giúp chúng tôi hiểu cách khách truy cập tương tác với trang web.
Những cookie này được sử dụng để cung cấp quảng cáo cá nhân hóa.