Thương hiệu phân phối chính hãng
Giỏ hàng

Mã lỗi Ricoh Aficio MP2014 — Trang 5/9

Code: 541-02

Description: Thermistor (center) disconnection: Low voltage An error is detected only when the input voltage at power-on is low. • Temperature of 0°C or lower is detected for 20 seconds continuously.
Causes: • Thermistor (center) disconnection • Thermistor (center) not connected correctly
Remedy: • Reconnect the thermistor (center). • Replace the thermistor (center). • Clear this SC by executing SP5-810-001.

Code: 542-01

Description: Reload failure: Thermistor deformation The temperature of 9°C or lower is detected five times consecutively for three seconds. • Measurement begins 15 seconds after the heater is turned on. • Measurement interval: 0.1 sec. • If the reload temperature is reached during measuring, the measurement is cancelled.
Causes: • Thermistor deformed • Thermistor out of position • Out of guaranteed input voltage
Remedy: • Replace the thermistor (center). • Clear this SC by executing SP5-810-001.

Code: 542-03

Description: Reload failure: Heater damage Normal (no pre-rotation): • The reload temperature is not reached for 35 seconds after heater control starts. Pre-rotation: • The reload temperature is not reached for 90 seconds after heater control starts.
Causes: • Heater damaged • After over-heat prevention
Remedy: • Replace the heater. • Clear this SC by executing SP5-810-001.

Code: 542-04

Description: Reload failure: Low voltage and thermistor deformation An error is detected only when the input voltage at power-on is low. The temperature of 7°C or lower is detected five times consecutively for 3 seconds. • Measurement begins 15 seconds after the heater is turned on. • Measurement interval: 0.1 sec. • If the reload temperature is reached during measuring, the measurement is cancelled.
Causes: • Thermistor deformed • Thermistor out of position • Out of guaranteed input voltage • After over-heat prevention
Remedy: • Replace the thermistor (center).

Code: 542-06

Description: Reload failure: Low voltage and heater deformation An error is detected only when the input voltage at power-on is low. • Normal (no pre-rotation): The reload temperature is not reached for 90 seconds after heater control starts. • Pre-rotation: The reload temperature is not reached for 285 seconds after heater control starts.
Causes: • Heater damaged • After over-heat prevention
Remedy: • Replace the heater.

Code: 543-00

Description: Thermistor (center) high temperature detection: Software An error is detected when the temperature of 230°C or higher is detected for 1 seconds continuously. • Detection with the thermistor (center) • Detection time: 10 or more • Measurement interval: 0.1 sec
Causes: • Triac short-circuit • MPU defective
Remedy: • Replace the MPU. • Clear this SC by executing SP5-810-001.

Code: 544-00

Description: Thermistor (center) high temperature detection: Hardware An error is detected when the temperature of 250°C or higher is detected • Detection with the thermistor (center)
Causes: • Triac short-circuit • MPU control board defective • Fusing control error
Remedy: • Replace the MPU. • Clear this SC by executing SP5-810-001.

Code: 545-01

Description: Heater continuously heat An error is detected when the target temperature cannot be reached for 10 seconds or more after reloading.
Causes: • Thermistor detection error • Heater damaged • After over-heat prevention
Remedy: • Replace the thermistor (center). • Replace the heater. • Clear this SC by executing SP5-810-001.
Đăng ký nhận bản tin Đăng ký nhận bản tin Đăng ký nhận bản tin Đăng ký nhận bản tin
Đăng ký nhận bản tin
Nhận ưu đãi sớm nhất khi chương trình diễn ra

Đăng ký nhận bản tin

Việc cho phép sử dụng cookie sẽ giúp cải thiện trải nghiệm của bạn trên trang web này. Chính sách cookie