Thương hiệu phân phối chính hãng
Giỏ hàng

Mã lỗi Ricoh Aficio MP3354 — Trang 8/40

Code: SC505-42

Description: Side LCIT Lower Limit Detection Error (D696) • Lower limit detection error (during descent) During tray initialization (upper limit not detected /lower limit eject detection), the tray base plate is lowered to check the tray base plate position, but the lower limit sensor is not detected although a predetermined time elapsed. Alternatively, at paper end, the tray base plate is lowered, but the lower limit sensor is not detected although a predetermined time elapsed. • Lower limit detection error (during ascent) During tray initialization (upper limit not detected/lower limit detection), the tray base plate is raised to check the tray base plate position, but the lower limit sensor is detected although a predetermined time elapsed. *If an error occurs for 3 times consecutively: the side LCIT transmits a "5th paper feed tray upper limit detection error" to the main machine. (The message of resetting the tray is displayed when the both sensors detect the error consecutively 2 times or less.)
Causes: • Lift motor error/connector missing • Lower limit sensor error/connector missing • Harness broken • Bank control board defective • Paper set fault • Timing belt damage/dropout • Timing pulley damage/dropout • Base plate damage/horizontality fault • Foreign matter, such as paper scrap, is caught inside the tray
Remedy: • Reset the paper. • Remove the foreign matter. • Replace the motor. • Reset the connector. • Replace the harness. • Replace the sensor. • Replace the control board for the optional side LCT. • Replace the tray. • Replace the timing belt. • Replace the timing pulley. • Replace the base plate.

Code: SC505-43

Description: Side LCIT Paper Overload Error (D696) During tray initialization, both the upper limit and lower limit are detected for 3 times consecutively. (The message of resetting the tray is displayed when the both sensors detect the error consecutively 2 times or less.)
Causes: • Paper overload • Paper set fault • Limit sensor error/connector missing • Lower limit sensor error/connector missing • Harness broken • Bank control board defective • Foreign matter, such as paper scrap, is caught inside the tray
Remedy: • Reset the paper. • Remove the foreign matter. • Reset the connector. • Replace the harness. • Replace the sensor. • Replace the control board for the optional side LCT.

Code: SC520-01

Description: Registration Motor: Lock. During motor ON, after checking the motor error notification registers (err_velo and err_posi) for 500msec, the error state of either register was detected at least 5 times.
Causes: • Motor defective • Connector disconnected • Harness broken • IOB defective • Encoder defective
Remedy: • Replace the motor. • Reset the connector. • Replace the harness. • Replace the IOB.

Code: SC520-02

Description: Paper feed Motor: Lock. During motor ON, after checking the motor error notification registers (err_velo and err_posi) for 500msec, the error state of either register was detected at least 5 times.
Causes: • Motor defective • Connector disconnected • Harness broken • IOB defective • Encoder defective
Remedy: • Replace the motor. • Reset the connector. • Replace the harness. • Replace the IOB.

Code: SC520-03

Description: Transport Motor: Lock. During motor ON, after checking the motor error notification registers (err_velo and err_posi) for 500msec, the error state of either register was detected at least 5 times.
Causes: • Motor defective • Connector disconnected • Harness broken • IOB defective • Encoder defective
Remedy: • Replace the motor. • Reset the connector. • Replace the harness. • Replace the IOB.

Code: SC521-01

Description: Duplex Entrance Motor: Lock. During motor ON, after checking the motor error notification registers (err_velo and err_posi) for 500msec, the error state of either register was detected at least 5 times.
Causes: • Motor defective • Connector disconnected • Harness broken • IOB defective • Encoder defective
Remedy: • Replace the motor. • Reset the connector. • Replace the harness. • Replace the IOB.

Code: SC521-02

Description: Duplex By-pass Motor: Lock. During motor ON, after checking the motor error notification registers (err_velo and err_posi) for 500msec, the error state of either register was detected at least 5 times.
Causes: • Motor defective • Connector disconnected • Harness broken • IOB defective • Encoder defective
Remedy: • Replace the motor. • Reset the connector. • Replace the harness. • Replace the IOB.

Code: SC522-00

Description: Paper Exit Motor: Lock During motor ON, after checking the motor error notification registers (err_velo and err_posi) for 500msec, the error state of either register was detected at least 5 times.
Causes: • Motor defective • Connector disconnected • Harness broken • IOB defective • Encoder defective
Remedy: • Replace the motor. • Reset the connector. • Replace the harness. • Replace the IOB.
Đăng ký nhận bản tin Đăng ký nhận bản tin Đăng ký nhận bản tin Đăng ký nhận bản tin
Đăng ký nhận bản tin
Nhận ưu đãi sớm nhất khi chương trình diễn ra

Đăng ký nhận bản tin

Việc cho phép sử dụng cookie sẽ giúp cải thiện trải nghiệm của bạn trên trang web này. Chính sách cookie