Thương hiệu phân phối chính hãng
Giỏ hàng

Mã lỗi Ricoh Aficio MP4000 — Trang 5/21

Code: 400

Description: Vsg adjustment error
Vsg is more than 4.2V or 3.8V or less when the machine adjusts Vsg value.
Causes: • Dirty or defective ID sensor • Defective ID sensor shutter

Code: 440

Description: Transfer belt bias error
The feed back bias from the transfer belt is more than 4V for 60 msec while the transfer belt bias is output. The A/D conversion level is 20 or less for 60 msec. The PWM duty is 24% or more for 60 msec.
Causes: • Power pack broken • Defective harness • Disconnected connector

Code: 441

Description: Transfer/Development motor errorThe machine detects a lock signal error from the transfer/development motor for 2 seconds after the transfer/development motor turned on.
Causes: • Overload on the motor • Defective transfer/development motor • Defective harness • Defective IOB

Code: 442

Description: Transfer belt contact motor error
The transfer belt HP sensor detects incorrect movement of the transfer belt after the transfer belt contact motor has turned on.
Causes: • Dirty transfer belt HP sensor • Defective transfer belt contact motor • Disconnected connector of the transfer belt HP sensor or motor • Disconnected cable • Defective IOB

Code: 501

Description: 1st tray lift malfunctionThe tray lift sensor is not activated after the tray lift motor has been on for 10 seconds. If the main power switch is turned on when the paper is already at the feed height, the paper height position is detected again. At this time, the tray lift sensor should de-activate within 1.5 sec after the paper bottom plate starts to drop. If it does not deactivate within 1.5 sec., a message will prompt the user to reset Tray 1. After two attempts to release the error by re-setting the paper tray, if this does not solve the problem then this SC is displayed.
Causes: • An obstruction (jammed paper, paper scraps, etc.) has blocked the motor drive and caused an overload. • Tray lift sensor connection loose, disconnected, or damaged • Tray lift sensor defective • Tray lift motor connection loose, disconnected, or damaged • Tray lift motor defective

Code: 502

Description: 2nd tray lift malfunction
The tray lift sensor is not activated after the tray lift motor has been on for 10 seconds. If the main power switch is turned on when the paper is already at the feed height, the paper height position is detected again. At this time, the tray lift sensor should de-activate within 1.5 sec. after the paper bottom plate starts to drop. If it does not deactivate within 1.5 sec., a message will prompt the user to reset Tray 2. After two attempts to re-set the paper tray, if this does not solve the problem then this SC is displayed.
Causes: • An obstruction (jammed paper, paper scraps, etc.) has blocked the motor drive and caused an overload. • Tray lift sensor connection loose, disconnected, or damaged • Tray lift sensor defective • Tray lift motor connection loose, disconnected, or damaged • Tray lift motor defective

Code: 503-1

Description: 3rd tray lift malfunction (optional paper feed unit or LCT)
For the paper feed unit: • SC 503-01 occurs if the lift sensor does not turn on within 10 seconds after the tray lift motor has turned on.
For the LCT: • SC 503-01 occurs if the lift sensor does not turn on or turn off within 8 seconds after the tray lift motor has turned on to lift or lower the tray.For the paper feed unit: • Defective tray lift motor or connector disconnection • Defective lift sensor or connector disconnection
For the LCT: • Defective stack transport clutch or connector disconnection • Defective tray motor or connector disconnection • Defective end fence home position sensor or connector disconnection • Defective upper limit sensor or connector disconnection • Defective tray lift motor or connector disconnection
Causes: • An obstruction (jammed paper, paper scraps, etc.) has blocked the motor drive and caused an overload. • Tray lift sensor connection loose, disconnected, or damaged • Tray lift sensor defective • Tray lift motor connection loose, disconnected, or damaged • Tray lift motor defective

Code: 503-2

Description: 3rd tray lift malfunction (optional paper feed unit or LCT)
For the paper feed unit: • When the tray lowers, the tray lift sensor does not go off within 1.5 sec.
For the LCT: • When the main switch is turned on or when the LCT is set, if the end fence is not in its position (home position sensor ON), the tray lift motor stops. • If the upper limit does not go off for 1.5 seconds even the tray lift moto
Causes: For the paper feed unit: • Defective tray lift motor or connector disconnection • Defective lift sensor or connector disconnection
For the LCT: • Defective stack transport clutch or connector disconnection • Defective tray motor or connector disconnection • Defective end fence home position sensor or connector disconnection
Đăng ký nhận bản tin Đăng ký nhận bản tin Đăng ký nhận bản tin Đăng ký nhận bản tin
Đăng ký nhận bản tin
Nhận ưu đãi sớm nhất khi chương trình diễn ra

Đăng ký nhận bản tin

Việc cho phép sử dụng cookie sẽ giúp cải thiện trải nghiệm của bạn trên trang web này. Chính sách cookie