Thương hiệu phân phối chính hãng
Giỏ hàng

Mã lỗi Ricoh Aficio MPC2503 — Trang 10/45

Code: SC492-00

Description: High voltage power source: image transfer/paper transfer: output error SC detection signal (transfer) is L (abnormal) for 200 ms consecutively during high voltage (transfer) output.
Causes: H/W error • Output power connector setting fault • Controller connector setting fault • Output high voltage Harness disconnection • Controller harness disconnection, short-circuit • Transfer unit setting fault • Control board_ IOB error (related signal error) • HVP_TTS error Load error • Increase in paper transfer roller impedance (low temperature environment/impedance rise/impedance rise due to dirt) • Operation fault of paper transfer contact mechanism • Increase in image transfer belt impedance • Opening in load power supply path
Remedy: • Reset or replacement the harness of high voltage power supply feed path • Reset or replace the harness between IOB-HVP_TTS • Reset or replace the transfer unit • Check operation of the contact mechanism • Replace the HVP_TTS • Replace the IOB

Code: SC493-00

Description: High voltage power source: DS development: output error "HVP:DS:output error detection signal" is detected “0” (abnormal) for 10 times consecutively (for 200ms) during output of the PWM signal used as an error detection target
Causes: • Leak harness fault • Unit fault • High voltage power source fault
Remedy: • Turn the power off/on • Reset or replacement the harness of high voltage power supply feed path • Reset or replace the unit • Replace the high voltage power source

Code: SC497-00

Description: Machine temperature detection thermistor error Temperature sensor output error: Below 0.56V (90 degrees or more), or above 3.0V (below -18 degrees)
Causes: • Connector disconnection or broken • Sensor defective
Remedy: • Check the sensor setting • Replace the imaging temperature sensor (thermistor)

Code: SC498-00

Description: Temperature and humidity sensor error Temperature sensor output error: Below 0.76V, or above 2.90V, or Moisture sensor output error: more than 2.4V
Causes: • Sensor not setting (disconnection or broken) • Sensor defective
Remedy: • Check the sensor setting • Replace the sensor

Code: SC501-01

Description: 1st Tray Lift Error The 1st tray lift motor error detection count reaches 3. (Up to 2, reset is displayed)
Causes: • 1st tray limit sensor connector missing, malfunction, dirt • 1st tray lift motor connector missing, disconnection, malfunction. • Foreign matter, such as paper scrap, is caught between the paper feed tray and the tray lift motor. • Paper set fault
Remedy: • Reset the paper • Remove the foreign matter 1st tray limit sensor, 1st tray lift motor • Check the harness • Reset the connector • Replacement 1st paper feed unit, 1st tray • Replacement Paper transport IOB • Replacement

Code: SC501-02

Description: 1st Tray Lowering Error The 1st tray descent motor error detection count reaches 5. (Up to 4, reset is displayed)
Causes: • 1st tray limit sensor connector missing, malfunction, dirt • 1st tray lift motor connector missing, disconnection, malfunction • Foreign matter, such as paper scrap, is caught between the paper feed tray and the tray lift motor. • Paper set fault • Paper overload
Remedy: • Reset the paper • Remove the foreign matter 1st tray limit sensor, 1st tray lift motor • Check the harness • Reset the connector • Replacement 1st paper feed unit, 1st tray • Replacement Paper transport IOB • Replacement

Code: SC502-01

Description: 2nd Tray Lift Error The 2nd tray lift motor error detection count reaches 3. (up to 2, reset is displayed)
Causes: • 2nd tray limit sensor connector missing, malfunction, dirt • 2nd tray lift motor connector missing, disconnection, malfunction • Foreign matter, such as paper scrap, is caught between the paper feed tray and the tray lift motor • Paper set fault
Remedy: • Reset the paper • Remove the foreign matter 2nd tray limit sensor, 2nd tray lift motor • Check the harness • Reset the connector • Replacement 2nd paper feed unit, 2nd tray • Replacement Paper transport IOB • Replacement

Code: SC502-02

Description: 2nd Tray Lowering Error The detection count of 2nd tray descent motor descent errors reaches a total of 5. (up to 4, reset is displayed)
Causes: • The 2nd paper feed tray limit sensor connector missing, malfunction, and dirt • 2nd tray lift motor connector missing, disconnection, malfunction • Foreign matter, such as paper scrap, is caught between the paper feed tray and the tray lift motor • Paper set fault • Paper overload
Remedy: • Reset the paper • Remove the foreign matter 2nd tray limit sensor, 2nd tray lift motor • Check the harness • Reset the connector • Replacement 2nd paper feed unit, 2nd tray • Replacement Paper transport IOB • Replacement
Đăng ký nhận bản tin Đăng ký nhận bản tin Đăng ký nhận bản tin Đăng ký nhận bản tin
Đăng ký nhận bản tin
Nhận ưu đãi sớm nhất khi chương trình diễn ra

Đăng ký nhận bản tin

Việc cho phép sử dụng cookie sẽ giúp cải thiện trải nghiệm của bạn trên trang web này. Chính sách cookie