Thương hiệu phân phối chính hãng
Giỏ hàng

Mã lỗi Ricoh Aficio MPC2800 — Trang 12/24

Code: 545

Description: Heating roller fusing lamp consecutive full power 1
When the fusing unit is not running in the ready condition, the heating roller fusing lamp keeps on full power for 8 seconds.
Causes: • Broken heating roller thermistor
Remedy: Replace the heating roller thermistor.

Code: 547

Description: Zero cross error
• The zero cross signal is detected three times even though the heater relay is off when turning on the main power. • The zero cross signal is not detected for 2 seconds even though the heater relay is on after turning on the main power or closing the front door. • The detection error occurs twice or more in the 11 zero cross signal detections. This error is defined when the detected zero cross signal is less than 45.
Causes: • Defective fusing lamp relay • Defective fusing lamp relay circuit • Unstable power supply
Remedy: 1. Check the power supply source. 2. Replace the PSU

Code: 551

Description: Pressure roller thermistor error
The temperature measured by the pressure roller thermistor does not reach 0 °C for 6 seconds.
Causes: • Loose connection of pressure roller thermistor • Defective thermopile • Defective pressure roller thermistor
Remedy: 1. Check that the pressure roller thermistor is firmly connected. 2. Replace the thermopile. 3. Replace the pressure roller thermistor.

Code: 552

Description: Pressure roller warm-up error
After the main switch is turned on or the door is closed, the pressure roller temperature does not reach the ready temperature within 70 seconds during fusing unit warm-up.
Causes: • Pressure roller fusing lamp broken
Remedy: 1. Check if the pressure roller thermistor is firmly connected. 2. Replace the pressure roller fusing lamp.

Code: 553

Description: Pressure roller fusing lamp overheat (software error)
The detected pressure roller temperature stays at 230°C or more for 1 second.
Causes: • Defective PSU • Defective IOB • Defective BICU
Remedy: 1. Replace the pressure roller thermistor. 2. Replace the PSU. 3. Replace the IOB. 4. Replace the BICU.

Code: 554

Description: Pressure roller fusing lamp overheat (hardware error)
The pressure roller thermistor detects 250°C or more.
Causes: • Defective PSU • Defective IOB • Defective BICU • Defective fusing control system
Remedy: 1. Replace the pressure roller thermistor. 2. Replace the PSU. 3. Replace the IOB. 4. Replace the BICU.

Code: 555

Description: Pressure roller lamp consecutive full power 2
When the fusing unit is not running in the ready condition, the pressure roller-fusing lamp keeps ON full power for 8 seconds or more.
Causes: • Broken pressure roller fusing lamp
Remedy: 1. Replace the pressure roller fusing lamp. 2. Replace the PSU.

Code: 555

Description: Pressure roller lamp consecutive full power 2
When the fusing unit is not running in the ready condition, the pressure roller-fusing lamp keeps ON full power for 8 seconds or more.
Causes: • Broken pressure roller fusing lamp
Remedy: 1. Replace the pressure roller fusing lamp. 2. Replace the PSU.
Đăng ký nhận bản tin Đăng ký nhận bản tin Đăng ký nhận bản tin Đăng ký nhận bản tin
Đăng ký nhận bản tin
Nhận ưu đãi sớm nhất khi chương trình diễn ra

Đăng ký nhận bản tin

Việc cho phép sử dụng cookie sẽ giúp cải thiện trải nghiệm của bạn trên trang web này. Chính sách cookie