Thương hiệu phân phối chính hãng
Giỏ hàng

Mã lỗi Ricoh Aficio MPC3002 — Trang 10/28

Code: 504

Description: Tray 4 error (Paper Feed Unit or LCT)
This SC is generated if the following condition occurs. For the two-tray paper feed unit When the tray lift motor is turned on, the upper limit is not detected within 15 seconds. For the LCT If the upper or lower limit is not detected within 8 seconds when the tray lift motor is turned on to lift up or lower the tray. This SC is generated too if the following condition occurs 3 consecutive times. For the two-tray paper feed unit When the tray lowers, the tray lift sensor does not go off within 1.5 sec. For the LCT If the upper limit does not go off for 1.5 seconds even the tray lift motor turns on to lower the tray after the upper limit has been detected at power on.
Causes: For the two-tray paper feed unit: • Defective tray lift motor or connector disconnection • Defective lift sensor or connector disconnection For the LCT: • Defective stack transport clutch or connector disconnection • Defective tray motor or connector disconnection • Defective end fence home position sensor or connector disconnection • Defective upper limit sensor or connector disconnection • Defective tray lift motor or connector disconnection
Remedy: 1. Check the cable connections. 2. Check and/or replace the defective component.

Code: 505

Description: Tray 5 error (Optional Paper Feed Unit or LCT)
This SC is generated if the following condition occurs. For the two-tray paper feed unit When the tray lift motor is turned on, the upper limit is not detected within 15 seconds. For the LCT 1200-sheet If the upper or lower limit is not detected within 8 seconds when the tray lift motor is turned on to lift up or lower the tray. This SC is generated too if the following condition occurs 3 consecutive times. For the two-tray paper feed unit When the tray lowers, the tray lift sensor does not go off within 1.5 sec. For the LCT 1200-sheet If the upper limit does not go off for 1.5 seconds even the tray lift motor turns on to lower the tray after the upper limit has been detected at power on.#a
Causes: • Defective tray lift motor or connector disconnection • Defective lift sensor or connector disconnection
Remedy: 1. Turn the power switch off and on.

Code: 520-01

Description: Registration motor error
The IOB does not receive the lock signal.
Causes: • Motor overload • Defective registration motor • Disconnected or broken harness • Defective IOB
Remedy: 1. Check the cable connection. 2. Replace the harness. 3. Replace the registration motor. 4. Replace the IOB.

Code: 520-02

Description: Paper feed motor error
The IOB does not receive the lock signal.
Causes: • Motor overload • Defective registration motor • Disconnected or broken harness • Defective IOB
Remedy: 1. Check the cable connection. 2. Replace the harness. 3. Replace the registration motor. 4. Replace the IOB.

Code: 530

Description: Fusing fan error
The IOB does not receive the lock signal 100 ms after turning on the fusing fan.
Causes: • Defective fusing fan motor or connector disconnection • Defective IOB
Remedy: 1. Check the connector and/or replace the fusing fan motor.

Code: 531

Description: QSU fan error
The machine does not detect the fan motor lock signal for 100 ms while the QSU fan turns on.
Causes: • Disconnected harness • Overload on the QSU fan motor • Defective QSU fan motor • Defective IOB
Remedy: 1. Check or replace the harness. 2. Replace the QSU fan. 3. Replace the IOB.

Code: 532-01

Description: Ventilation fan (at the left side of the machine) motor error: front end
The IOB does not receive the lock signal for 100 ms after turning on the ventilation fan motor in the front end or rear end.
Causes: • Defective ventilation fan motor in the front end or rear end • Defective IOB
Remedy: 1. Replace the ventilation fan (at the left side of the machine) motor in the front end or rear end. 2. Replace the IOB.

Code: 532-02

Description: Ventilation fan (at the left side of the machine) motor error: rear end
The IOB does not receive the lock signal for 100 ms after turning on the ventilation fan motor in the front end or rear end.
Causes: • Defective ventilation fan motor in the front end or rear end • Defective IOB
Remedy: 1. Replace the ventilation fan (at the left side of the machine) motor in the front end or rear end. 2. Replace the IOB.
Đăng ký nhận bản tin Đăng ký nhận bản tin Đăng ký nhận bản tin Đăng ký nhận bản tin
Đăng ký nhận bản tin
Nhận ưu đãi sớm nhất khi chương trình diễn ra

Đăng ký nhận bản tin

Việc cho phép sử dụng cookie sẽ giúp cải thiện trải nghiệm của bạn trên trang web này. Chính sách cookie