Thương hiệu phân phối chính hãng
Giỏ hàng

Mã lỗi Ricoh Aficio MPC401SRSP — Trang 7/25

Code: 442

Description: Image transfer belt contact motor error The image transfer belt contact sensor does not detect the movement of actuator at the sensor while the polygon motor rotates.
Causes: • Dirty image transfer belt contact sensor • Defective image transfer belt contact motor • Disconnected connector of image transfer belt contact sensor or motor • Disconnected cable • Broken +24V fuse on PSU • Defective interlock switches • Defective BCU
Remedy: • Replace the image transfer belt contact sensor. • Replace the image transfer belt contact motor. • Replace the +24V fuse on the PSU. • Replace the interlock switches. • Replace the BCU.

Code: 443

Description: Image transfer unit error The machine detects the encoder sensor error.
Causes: • Defective encoder sensor • Image transfer unit installation error • Defective image transfer unit motor
Remedy: • Check if the image transfer unit is correctly set. • Replace the image transfer unit motor. • Replace the image transfer unit.

Code: 452

Description: Paper transfer unit contact error The paper transfer unit contact sensor does not detect the movement of actuator at the sensor while the polygon motor rotates.
Causes: • Defective paper transfer unit contact sensor • Defective paper transfer unit contact motor • Broken +24V fuse on PSU • Defective BCU
Remedy: • Check the connection between the paper transfer unit and PSU. • Replace the paper transfer unit contact sensor. • Replace the paper transfer unit contact motor. • Replace the +24V fuse on the PSU. • Replace the BCU.

Code: 460

Description: Separation power pack output error An interrupt checks the status of the power pack every 20 ms. This SC is issued if the BCU detects a short in the power pack 10 times at D(ac).
Causes: • Damaged insulation on the HVPS: D cable • Damaged insulation around the HVPS: D.
Remedy: • Replace the HVPS: D cable. • Replace the HVPS: D.

Code: 491

Description: High voltage power: Drum/ development bias output error An error signal is detected for 0.2 seconds when charging the drum or development.
Causes: • High voltage leak • Broken harness • Defective drum unit or development unit • Defective HVPS: CB
Remedy: • Check or replace the harness. • Replace the drum unit or paper transfer unit. • Replace the HVPS: CB.

Code: 492

Description: High voltage power: Image transfer/ paper transfer bias output error An error signal is detected for 0.2 seconds when charging the separation, image transfer bet or paper transfer roller.
Causes: • High voltage open • Broken harness • Defective image transfer belt unit or paper transfer unit • Defective HVPS: T1T2
Remedy: • Check or replace the harness. • Replace the image transfer belt unit or paper transfer unit. • Replace the HVPS: T1T2.

Code: 495

Description: Toner collection motor error The machine detects that the toner collection bottle is not set for one second when the toner collection motor is turned off.
Causes: • Toner collection motor damaged • Disconnect or defective harness
Remedy: • Check or replace the harness. • Replace the toner collection motor. • Check and retry the connecting procedure.

Code: 498

Description: Temperature and humidity sensor error • The thermistor output of the temperature sensor was not within the prescribed range (0.5V to 2.8V). • The thermistor output of the humidity sensor was not within the prescribed range (0.01V to 2.4V).
Causes: • Temperature and humidity sensor harness disconnected, loose, defective • Temperature and humidity sensor defective
Remedy: • Check the connector and harness. • Replace the temperature/humidity sensor.
Đăng ký nhận bản tin Đăng ký nhận bản tin Đăng ký nhận bản tin Đăng ký nhận bản tin
Đăng ký nhận bản tin
Nhận ưu đãi sớm nhất khi chương trình diễn ra

Đăng ký nhận bản tin

Việc cho phép sử dụng cookie sẽ giúp cải thiện trải nghiệm của bạn trên trang web này. Chính sách cookie