Thương hiệu phân phối chính hãng
Giỏ hàng

Mã lỗi Ricoh Aficio MPC6003SP

Code: 543-00

Description: Fusing central thermopile high temperature detection (software) Above (T3) degrees C detected for (t4) seconds continuously. Detection period 100ms, detection count: 10 times or more.
Causes: • Triac short-circuit • IOB board defective • BCU board defective
Remedy: • Replace the IOB board • Replace the BCU board • Replace the fusing unit

Code: 549-01

Description: Shield Operation Error Detection During HP detection operation, shield sensors 1 and 2 detect "High" for (t30) seconds continuously.
Causes: • Motor defective • Sensor defective • Sensor actuator/feeler modification/defective • Shield modification/defective
Remedy: • Replace the motor • Replace the HP sensor • Replace the fusing unit

Code: 549-02

Description: Shield Operation Error Detection During shield basic operation, shield sensor 2 does not go "Low > High" even if (t31) seconds elapsed from screen motor rotation start.
Causes: • Motor defective • Sensor defective • Sensor actuator/feeler modification/defective • Shield modification/defective
Remedy: • Replace the motor • Replace the HP sensor • Replace the fusing unit

Code: 549-03

Description: Shield Operation Error Detection During shield basic operation, shield motor does not stop even if (t32) seconds elapsed from rotation start.
Causes: • Motor defective • Sensor defective • Sensor actuator/feeler modification/defective • Shield modification/defective
Remedy: • Replace the motor • Replace the HP sensor • Replace the fusing unit

Code: 549-04

Description: Shield Operation Error Detection During HP detection operation, HP detection fails 3 times consecutively.
Causes: • Motor defective • Sensor defective • Sensor actuator/feeler modification/defective • Shield modification/defective
Remedy: • Replace the motor • Replace the HP sensor • Replace the fusing unit

Code: SC101-01

Description: Lamp Error (Scanning) The white level peak did not reach the prescribed threshold when the white plate was scanned.
Causes: • LED defective • IDB (LED driver) defective • SBU defective • IPU defective • Power/signal harness defective • Condensation in scanner unit • Mirrors or lenses dirty or positioned incorrectly • White plate dirty or installed incorrectly
Remedy: 1. Turn the power off/on. 2. Perform the following operations: • Reconnect the power/signal harness. • Reattach/clean the mirrors/lenses. • Reattach/clean the white plate. 3. Replace the following parts: • Replace the LED board. • Replace the IDB board or SIO board. • Replace the SBU board. • Replace the IPU board. • Replace the power/signal harness.

Code: SC101-02

Description: Lamp Error (LED illumination adjustment) LED error was detected.
Causes: • LED defective • IDB (LED driver) defective • Power/signal harness defective
Remedy: 1. Turn the power off/on. 2. Perform the following operations: • Reconnect the power/signal harness. 3. Replace the following parts: • Replace the LED board. • Replace the IDB board or SIO board. • Replace the power/signal harness.

Code: SC102-00

Description: LED Illumination Adjustment Error The white level peak reached the prescribed threshold when the white plate was scanned after a specified number of adjustments.
Causes: • LED defective • IDB (LED driver) defective • SBU defective • IPU defective • Power/signal harness defective
Remedy: 1. Turn the power off/on. 2. Reconnect the power/signal harness. 3. Replace the following parts: • Replace the LED board. • Replace the SBU board. • Replace the IDB board or SIO board. • Replace the IPU board. • Replace the power/signal harness.
Đăng ký nhận bản tin Đăng ký nhận bản tin Đăng ký nhận bản tin Đăng ký nhận bản tin
Đăng ký nhận bản tin
Nhận ưu đãi sớm nhất khi chương trình diễn ra

Đăng ký nhận bản tin

Việc cho phép sử dụng cookie sẽ giúp cải thiện trải nghiệm của bạn trên trang web này. Chính sách cookie