Thương hiệu phân phối chính hãng
Giỏ hàng

Mã lỗi Ricoh Aficio MPC8002SP — Trang 34/63

Code: SC551-00

Description: Sensor 4: Pressure Roller Center Disconnection 0 degrees or lower was detected for (t1) seconds consecutively. Number of times: 10 or more D135 (Japan): 75 (seconds) D136 (Japan)/D135 (NA): 75 (seconds) D136 (NA)/D135 (EU)/D136(EU): 75 (seconds) D137 (Japan): 75 (seconds) D138 (Japan)/D137 (NA)/D138 (NA)/D137 (EU)/D138 (EU): 75 (seconds) Monitored at: All times, though SC is not issued when temperature is not controlled (when in off mode/sleep mode, when a door, excluding the toner supply door, is open, or when the heater relay is off).
Causes: • Thermopile disconnection • Connecter contact failure
Remedy: • Replace the thermopile. • Reconnect the connector. • Replace the connector. • Replace the connector.

Code: SC552-02

Description: Sensor 4: Heating Roller Center: Reload Failure: Timeout 1 Failed to reach (T2) degrees centigrade after (t4) seconds from the start of heater control. D135 (Japan):T2 = 45, t4 = 80 D136 (Japan)/D135 (NA): T2 = 45, t4 = 60 D136 (NA)/D135 (EU)/D136(EU): T2 = 45, t4 = 60 D137 (Japan): T2 = 45, t4 = 60 D138 (Japan)/D137 (NA)/D138 (NA)/D137 (EU)/D138 (EU): T2 = 45, t4 = 60 Monitored at: Startup (Power-on, when a cover is closed, when fuser heater is under control)
Causes: • Thermistor deformed or floating • Input voltage out of specification
Remedy: • Replace the thermopile. • Use with supported input voltage • Replace the pressure roller heater. • Replace the unit.

Code: SC552-03

Description: Sensor 4: Heating Roller Center: Reload Failure: Timeout 2 Failed to reach reload temperature after (t5) seconds from the start of heater control. D135 (Japan):t5 = 230 D136 (Japan)/D135 (NA): t5 = 230 D136 (NA)/D135 (EU)/D136(EU): t5 = 230 D137 (Japan): t5 = 230 D138 (Japan)/D137 (NA)/D138 (NA)/D137 (EU)/D138 (EU): t5 = 230 Monitored at: Startup (Power-on, when a cover is closed, when fuser heater is under control)
Causes: • Pressure heater malfunctioning • Overheating prevention device worked.
Remedy: • Replace the thermopile. • Use with supported input voltage • Replace the pressure roller heater. • Replace the unit.

Code: SC553-00

Description: Sensor 4: Pressure Roller Center: Overheat detection (software) (T3) degrees centigrade or higher was detected for (t6) seconds consecutively. Number of times: 10 or more D135 (Japan):T3 = 220, t6 = 1 D136 (Japan)/D135 (NA): T3 = 220, t6 = 1 D136 (NA)/D135 (EU)/D136(EU): T3 = 220, t6 = 1 D137 (Japan): T3 = 220, t6 = 1 D138 (Japan)/D137 (NA)/D138 (NA)/D137 (EU)/D138 (EU): T3 = 220, t6 = 1 Monitored at: All times, though SC is not issued when temperature is not controlled (when in off mode/sleep mode, when a door, excluding the toner supply door, is open, or when the heater relay is off).
Causes: • Triac shorted. • IOB board defective.
Remedy: • Replace the IOB board. • Replace the unit.

Code: SC554-00

Description: Pressure Roller Center: Overheat detection (hardware) Hardware detection of overheat condition. The pressure roller center thermopile was detected as the cause.
Causes: • IOB defective • Fuser control software running out of control • Triac damaged (shorted). • Pressure roller center thermopile defective
Remedy: • After removing the cause of the SC, Set "Fusing SC Clear" in the SP mode. • If necessary, replace: IOB/pressure roller center thermopile/AC drive.

Code: SC555-00

Description: Heater 2: Heater Continuously On (Sensor 4: Thermopile: Pressure Roller Center) Target temperature was not reached (t7) seconds after reload. Time elapsed after reload (excluding paper transport time) (t8) D135 (Japan): t7 = 90, t8 = 90 D136 (Japan)/D135 (NA): t7 = 90, t8 = 90 D136 (NA)/D135 (EU)/D136(EU): t7 = 90, t8 = 90 D137 (Japan): t7 = 90, t8 = 90 D138 (Japan)/D137 (NA)/D138 (NA)/D137 (EU)/D138 (EU): t7 = 90, t8 = 90 Monitored at: All times, though SC is not issued when temperature is not controlled (when in off mode/sleep mode, when a door, excluding the toner supply door, is open, or when the heater relay is off).
Causes: • Thermopile detection error • Heater disconnection • Overheating prevention device worked.
Remedy: • Replace the thermopile. • Replace the heater. • Replace the unit.

Code: SC557-00

Description: Zero Cross Error (high frequency)
Causes: • Unstable commercial power supply frequency
Remedy: No action required.

Code: SC559-00

Description: Fusing jam: 3 counts Fusing jam (fusing exit sensor late jam) was detected 3 times consecutively. Details: This SC can be set ON/OFF. The factory setting is OFF; set it ON when requested by the customer. SP1-142-001: 0: OFF (factory setting) 1: ON (set by service personnel at the request of customer) This prevents collateral problems (such as thermistor floating) that may be caused by repeated jams in the fusing unit. • The jam counter is not reset by power off/on. • When paper is output successfully, the jam counter is reset.
Causes: • Paper jam in the fusing unit • Sensor defective
Remedy:
Đăng ký nhận bản tin Đăng ký nhận bản tin Đăng ký nhận bản tin Đăng ký nhận bản tin
Đăng ký nhận bản tin
Nhận ưu đãi sớm nhất khi chương trình diễn ra

Đăng ký nhận bản tin

Việc cho phép sử dụng cookie sẽ giúp cải thiện trải nghiệm của bạn trên trang web này. Chính sách cookie