Thương hiệu phân phối chính hãng
Giỏ hàng

Mã lỗi Ricoh Aficio SP3600SF — Trang 5/14

Code: SC557-00

Description: Zero-crossing frequency exceeded
Causes: The number of zero-crossing interrupts exceeds a certain value in 500 ms. The frequency of the commercial power supply line is unstable or noise occurs.
Remedy: None

Code: SC559-00

Description: Fusing jam detected 3 times in succession
Causes: Fusing jam is detected three times in succession. Paper is wrapped around the fusing roller.
Remedy: Clear the SP: fusing SC.

Code: SC641-00

Description: • Communication error: Engine (Timeout error) • Communication error: Engine (Retry error)
Causes: • There is no response from the engine even after the timeout period specified during the communication has elapsed. • The communication has failed when sending the normal mode (ESIF_LECI_NORMAL) command even after exceeding the maximum number of command transmission retry. • Controller board/software defective • The connection between the controller board and engine board is faulty. • Engine board/software defective
Remedy: • Check the connection between the controller board and engine board. • Turn the main power off/on.

Code: SC653-00

Description: Incorrect remote service ID2
Causes: If the serial number*1 for producing ID2*2 has any of the following problems: • Blank • Contains control characters • Cannot be read *1: The serial number refers to "Machine Serial Set" (SP5-811-001). *2: ID2 refers to "Machine No. Setting" (SP5-811-003). • The serial number was not specified at the factory. • The NV memory is corrupted and cannot be read. • The NV memory has been corrupted while writing data into it.
Remedy: • Turn the main power off/on. If the problem persists, the hardware is faulty.

Code: SC669-01 ... SC669-26

Description: EEPROM communication error
Causes: An error is notified during EEPROM communication and the printer does not recover after three retries. 669 - 1 ID error during EEPROM OPEN 669 - 2 Channel error during EEPROM OPEN 669 - 3 Device error during EEPROM OPEN 669 - 4 Communication interrupted error during EEPROM OPEN 669 - 5 Communication timeout error 669 - 6 Not operating error during EEPROM OPEN 669 - 7 Buffer full during EEPROM OPEN 669 - 8 No error code during EEPROM OPEN 669 - 9 ID error 669 - 10 No error code during EEPROM Close 669 - 11 ID error during EEPROM data write 669 - 12 Channel error during EEPROM data write 669 - 13 Device error during EEPROM data write 669 - 14 Communication interrupted error during EEPROM data write 669 - 15 Communication timeout error 669 - 16 Not operating error during EEPROM data write 669 - 17 Buffer full during EEPROM data write 669 - 18 No error code during EEPROM data write 669 - 19 ID error during EEPROM data read 669 - 20 Channel error EEPROM data read 669 - 21 Device error during EEPROM data read 669 - 22 Communication interrupted error during EEPROM data read 669 - 23 Communication timeout error 669 - 24 Not operating error during EEPROM data rea• Electromagnetic noise • EEPROM errord 669 - 25 Buffer full during EEPROM data read 669 - 26 No error code during EEPROM data read • Electromagnetic noise • EEPROM error
Remedy: • Turn the main power OFF and then ON. • Replace the BCU

Code: SC669-36

Description: EEPROM communication error
Causes: The EEPROM data has been transferred to the SRAM twice in succession, but the two sets of transferred data do not match. 669 - 36 EEPROM SRAM OPEN: Verified error • Electromagnetic noise • EEPROM error
Remedy: • Turn the main power OFF and then ON.

Code: SC670-00

Description: Engine start up error
Causes: • The /ENGRDY signal is not detected even after the specified time has elapsed after turning the main power on or restoring from energy saver mode. • The /ENGRDY signal is detected, but it is negated at an unexpected occasion*. * Expected negation occurs when turning the power off, switching to the energy saver mode (after the engine automatically goes off), and rebooting the machine. • The engine board does not start up. • The connection between the controller board and engine board is faulty.
Remedy: Check the connection between the engine board and the controller board. • If this problem always occurs, replace the engine board. If the problem persists, consider replacing the controller board or other boards between them. • If this problem occasionally occurs, multiple causes are to be considered, such as the software, engine board, controller board, and PSU.

Code: SC681

Description: Device ID is not identified (toner cartridge)
Causes: An error is notified during the ID identification after three retries. 681 - 1 Device ID error (Incorrect ID) 681 - 6 Channel error 681 - 11 Device ID error (No ID chip) 681 - 16 Communication Error 681 - 21 Communication timeout 681 - 26 The device has stopped its operation 681 - 31 The requested buffer is full 681 - 36 EEPROM SRAM OPEN: Verification error
Remedy: • Turn the main power OFF and then ON. • Replace the toner cartridge (ID chip)
Đăng ký nhận bản tin Đăng ký nhận bản tin Đăng ký nhận bản tin Đăng ký nhận bản tin
Đăng ký nhận bản tin
Nhận ưu đãi sớm nhất khi chương trình diễn ra

Đăng ký nhận bản tin

Việc cho phép sử dụng cookie sẽ giúp cải thiện trải nghiệm của bạn trên trang web này. Chính sách cookie