Thương hiệu phân phối chính hãng
Giỏ hàng

Mã lỗi Ricoh Aficio SP4510DN — Trang 8/35

Code: SC652-00

Description: Remote service ID2 mismatching
Causes: There was an authentication mismatch between ID2 for @Remote, the controller board, and NVRAM. • Used controller board installed • Used NVRAM installed (such action is not allowed.)
Remedy: • If this occurs during RC Gate installation: Check the validity of the certificate and the NVRAM, check the machine serial number, write the common certificate, and then begin installation again. • If this occurs after RC Gate installation: Clear the RC Gate install status, check the validity of the certificate and the NVRAM, check the machine serial number, write the common certificate, and then begin installation again.

Code: SC653-00

Description: Incorrect remote service ID2
Causes: ID2 stored in the NVRAM has either of the following problems. • Number of characters is not 17. • Includes a character that cannot be printed. • All spaces • NULL
Remedy: Replace the NVRAM. Clear the RC Gate install ationstatus, write the common certificate, and then begin installation again.

Code: SC669

Description: EEPROM communication error
Causes: An error is notified during EEPROM669 - 1 ID error during EEPROM OPEN 669 - 2 Channel error during EEPROM OPEN 669 - 3 Device error during EEPROM OPEN 669 - 4 Communication interrupted error during EEPROM OPEN 669 - 5 Communication timeout error 669 - 6 Not operating error during EEPROM OPEN 669 - 7 Buffer full during EEPROM OPEN 669 - 8 No error code during EEPROM OPEN 669 - 9 ID error 669 - 10 No error code during EEPROM Close 669 - 11 ID error during EEPROM data write 669 - 12 Channel error during EEPROM data write 669 - 13 Device error during EEPROM data write 669 - 14 Communication interrupted error during EEPROM data write 669 - 15 Communication timeout error 669 - 16 Not operating error during EEPROM data write 669 - 17 Buffer full during EEPROM data write 669 - 18 No error code during EEPROM data write 669 - 19 ID error during EEPROM data read 669 - 20 Channel error EEPROM data read 669 - 21 Device error during EEPROM data read 669 - 22 Communication interrupted error during EEPROM data read 669 - 23 Communication timeout error 669 - 24 Not operating error during EEPROM data read 669 - 25 Buffer full during EEPROM data read 669 - 26 No error code during EEPROM data read • Electromagnetic noise • EEPROM error
Remedy: • Turn the main power OFF and then ON. • Replace the BICU

Code: SC669-36

Description: EEPROM communication error
Causes: The EEPROM data has been transferred to the SRAM twice in succession, but the two sets of transferred data do not match. 669 - 36 EEPROM SRAM OPEN: Verified error • Electromagnetic noise • EEPROM error
Remedy: • Turn the main power OFF and then ON.

Code: SC670-00

Description: Engine start up error
Causes: • Case 1 • /ENGRDY signal was not asserted when the machine was turned on or returned from energy saver mode. • /IPURDY signal was not asserted when the machine was turned on or returned from energy saver mode. • The EC response from the engine was not received within the specified time after turning on the power. • The PC response from the engine was not received within the specified time after turning on the power. • The SC response from the engine was not received within the specified time after turning on the power (MFP models only). • Writing to Rapi driver failed (the other party not found through PCI). • Case 2 • Unexpected down status was detected after /ENGRDY assertion. • Case 1 • Engine board does not start up. • Case 2 • Engine board reset unexpectedly.
Remedy: Check the connection between the engine board and the controller board. • If this problem always occurs, replace the engine board. If the problem persists, consider replacing the controller board or other boards between them. • If this problem occasionally occurs, multiple causes are to be considered, such as the software, engine board, controller board, and PSU.

Code: SC672-10

Description: Controller start up error
Causes: The controller and control panel failed to establish communication when the power was turned on. • Controller stalled • Board installed incorrectly • Controller board defective • Operation panel connector is loose, broken, or defective • Controller's late response
Remedy: • Turn the main power off/on. • Check the connection of the controller board. • Replace the controller board. • Check the control panel harness.

Code: SC672-11

Description: Controller start up error
Causes: After the machine was powered on, communication between the controller and the operation panel was not established, or data transmission failed after a normal startup. • Controller stalled • Board installed incorrectly • Controller board defective • Operation panel connector is loose, broken, or defective • Controller's late response
Remedy: • Turn the main power off/on. • Check the connection of the controller board. • Replace the controller board. • Check the control panel harness.

Code: SC672-12

Description: Controller start up error
Causes: Communication with controller was interrupted after a normal startup. • Controller stalled • Board installed incorrectly • Controller board defective • Operation panel connector is loose, broken, or defective • Controller's late response
Remedy: • Turn the main power off/on. • Check the connection of the controller board. • Replace the controller board. • Check the control panel harness.
Đăng ký nhận bản tin Đăng ký nhận bản tin Đăng ký nhận bản tin Đăng ký nhận bản tin
Đăng ký nhận bản tin
Nhận ưu đãi sớm nhất khi chương trình diễn ra

Đăng ký nhận bản tin

Việc cho phép sử dụng cookie sẽ giúp cải thiện trải nghiệm của bạn trên trang web này. Chính sách cookie