Thương hiệu phân phối chính hãng
Giỏ hàng

Mã lỗi Ricoh B163 Aficio 2051 MT-C2

Code: 101

Description: Exposure Lamp Error
At trigger on, the lamp was not detected on.
Causes: • Exposure lamp defective
• Lamp regulator defective
• Lamp regulator harness damaged, disconnected
• Dirty standard white plate
• Scanner mirror dirty or out of position
• Lens dirty, out of position
• SBU board defective

Code: 120

Description: Scanner home position error 1
The scanner HP sensor does not detect the on condition during initialization or copying.
Causes: • BCU, SDRB (Scanner Driver Board) defective
• Scanner motor defective
• Harness between BCU, SDRB, scanner motor disconnected.
• Scanner HP sensor defective.
• Harness between scanner HP sensor and BCU disconnected.
• Scanner wire, timing belt, pulley, carriage installed incorrectly.

Code: 121

Description: Scanner home position error 2
The scanner HP sensor does not detect the off condition during initialization or copying.
Causes: • BCU, SDRB (Scanner Driver Board) defective
• Scanner motor defective
• Harness between BCU, SDRB, scanner motor disconnected
• Scanner HP sensor defective
• Harness between scanner HP sensor and BCU disconnected
• Scanner wire, timing belt, pulley, carriage installed incorrectly.

Code: 122

Description: Scanner home position error 3
The scanner home position sensor does not detect the on condition during original scanning.
Causes: • BCU, SDRB (Scanner Driver Board) defective
• Scanner motor defective
• Harness between BCU, SDRB, scanner motor disconnected
• Scanner HP sensor defective
• Harness between scanner HP sensor and BCU disconnected
• Scanner wire, timing belt, pulley, carriage installed incorrectly

Code: 123

Description: Scanner home position error 4
The scanner home position sensor does not detect the off condition during original scanning.
Causes: • BCU, SDRB (Scanner Driver Board) defective
• Scanner motor defective
• Harness between BCU, SDRB, scanner motor disconnected
• Scanner HP sensor defective
• Harness between scanner HP sensor and BCU disconnected
• Scanner wire, timing belt, pulley, carriage installed incorrectly.

Code: 143

Description: SBU auto adjust error
Automatic adjustment of the SBU fails when the machine is switched on.
Causes: • Exposure lamp defective
• Exposure lamp regulator defective
• Harness between exposure lamp and lamp regulator is disconnected
• White plate installed incorrectly or is dirty
• Scanning mirrors of the exposure unit are dirty or out of position
• SBU board defective
• VIB board defective.
• Harness between SBU, VIB disconnected
• Harness between VIB, BCU disconnected

Code: 144

Description: SBU transmission error
After the SBU switches on, the BCU detects one of the following conditions on the SBU:
• 1 s after power on, the SYDI signal does not go high, even after 1 retry.
• 1 s after power on, the SYDI signal goes high, but the SBU ID could not be read after 3 attempts.
Causes: • SBU defective
• VIB defective
• Harness (40-pin shielded) between the SBU, VIB is disconnected
• Harness (shielded cable) between the VIB, BCU is disconnected

Code: 165

Description: Copy data security unit error B828
The copy data security option is installed by not operating correctly.
Causes: • Copy data security card corrupted
• The board is not installed or the board is defective
• IPU board defective
Đăng ký nhận bản tin Đăng ký nhận bản tin Đăng ký nhận bản tin Đăng ký nhận bản tin
Đăng ký nhận bản tin
Nhận ưu đãi sớm nhất khi chương trình diễn ra

Đăng ký nhận bản tin

Việc cho phép sử dụng cookie sẽ giúp cải thiện trải nghiệm của bạn trên trang web này. Chính sách cookie