Thương hiệu phân phối chính hãng
Giỏ hàng

Mã lỗi Ricoh B235 MP1100 B-C3 — Trang 13/25

Code: SC650

Description: NRS Modem Communication Error
One of the following factors could be the cause of this error:
• In the User Tools, check the settings for the dial-up user name and dial up password.
• Modem has been disconnected. • Modem board disconnected.
Causes: Check the following for a machine that is using Cumin (NRS modem):
• An error was returned during the dialup connection
• A network was detected at startup
• At startup the machine detected that the NIB was disabled, or did not detect a modem board

Code: SC651

Description: Illegal Remote Service Dial-up
An expected error occurred when Cumin-M dialed up the NRS Center.
Causes: • Software bug
• No action is required because only the count is logged

Code: SC670

Description: Engine Startup Error
At power on or after the machine leaves the energy conservation mode:
• ENGRDY signal does not assert
• IPURDY signal does not assert After power on and the prescribed time has elapsed:
• No EC response from the engine
• No PC response from the engine
• No SC response from the engine During machine operation mode:
• Write to Rapi drive failure (could not locate destination on the PCI)
• After the /ENGRDY signal asserts with no effect.
Causes: • BCU ÅÆ Controller Board disconnected
• BCU board defective
• Controller board defective
• Mother board defective
• Software error; switch off/on, if that fails, change the engine firmware
• PSU-E or PSU-C defective

Code: SC672

Description: Controller Startup Error
The line between the controller board and the operation panel does not open correctly when the machine is powered on, or after the machine was powered on communication between the controller and operation panel is suspended. The controller board and operation panel could not exchange the handshake (FDH) and acknowledge (FEH) signals within 15 s of the operation panel reset after power on, or after 2 retries there was no response to the transmission line confirmation command issued every 30 s from the operation panel to the controller board.
Causes: • Controller board defective
• Controller board installed incorrectly
• Operation panel harness connection loose or incorrect

Code: SC701

Description: ADF Pickup Roller Release Malfunction
The pick-up roller HP sensor does not activate or de-activate when the pick-up motor turns on.
Causes: • HP sensor connector, harness loose, broken, defective
• Pick-up motor connector, harness loose, broken defective
• Pick-up roller HP sensor defective
• Pick-up motor defective
• ADF main control board defective

Code: SC702

Description: ADF Feed-In Motor Error
While the feed motor is operating, the encoder pulse signal is not received within the specified time, or the paper size length encoder signal cannot be detected within the specified time (the encoder is built into the feed-in motor).
Causes: • Feed-in motor connector, harness loose, broken, defective
• Paper length sensor connector, harness loose, broken, defective
• Feed-in motor defective
• Paper length sensor or encoder is defective
• ADF main control board defective

Code: SC703

Description: ADF Transport Belt Motor Error
While the motor is operating, the encoder pulse signal is not received within the specified time and the transport belt motor does not turn properly.
Causes: • Transport belt motor defective
• Poor connection between the transport motor and ADF main board
• ADF main board defective

Code: SC704

Description: ADF Feed-Out Motor Error
While the feed-out motor is operating, the encoder pulse signal is not received within the specified time, and the feed-out motor does not turn properly
Causes: • Feed-out motor defective
• Poor connection between the feed-out motor and ADF main board
• ADF main control board defective
Đăng ký nhận bản tin Đăng ký nhận bản tin Đăng ký nhận bản tin Đăng ký nhận bản tin
Đăng ký nhận bản tin
Nhận ưu đãi sớm nhất khi chương trình diễn ra

Đăng ký nhận bản tin

Việc cho phép sử dụng cookie sẽ giúp cải thiện trải nghiệm của bạn trên trang web này. Chính sách cookie