Description: Temperature and humidity sensor error The output of the temperature sensor was not within the prescribed range (0.5V to 4.2V) for 3 minutes.
Causes: • Temperature and humidity sensor harness disconnected, loose, defective • Temperature and humidity sensor defective
Remedy: 1. Check the connector and harness. Replace the temperature/humidity sensors below the black PCDU and yellow PCDU.
Description: Tray 1 (tandem tray) feed error • The tray 1 lift sensor does not switch on 10 s after the tray lift motor switches on and starts lifting the bottom plate. • When the tray lowers, the tray lift sensor does not go off within 1.5 sec.
Causes: • Tray lift motor 1 defective or disconnected • Paper or other obstacle trapped between tray and motor • Pick-up solenoid 1 disconnected or blocked by an obstacle
Remedy: 1. Check the harness connection. 2. Check or clear obstacles between tray and motor.
Description: Tray 2 (universal tray) feed error • The lift sensor is not activated within 10 seconds after the tray lift motor starts lifting the bottom plate. • When the tray lowers, the tray lift sensor does not go off within 1.5 sec.
Causes: • Tray lift motor 2 defective or disconnected • Paper or other obstacle trapped between tray and motor • Pick-up solenoid 2 disconnected or blocked by an obstacle
Remedy: 1. Check the harness connection. 2. Check or clear obstacles between tray and motor. 3. Check or clear obstacles around the pick-up solenoid.
Description: Tray 3 (A4 LCT) feed error (G178/M078 only) One of the following conditions is detected in tray 3, 4 or 5 of the A4 LCT: The tray 3, 4 or 5 lift sensor is not activated for 10 s after the tray 3, 4 or 5 lift motor turned on. Upper limit is not detected within 10 s while the paper tray is lifting during paper feed. The tray 3, 4 or 5 lift sensor is already activated when tray 3, 4 or 5 is placed in the machine
Causes: • Poor connection or defective tray 3, 4 or 5 lift motor • Poor connection or defective tray 3, 4 or 5 lift sensor • Remaining paper or another obstruction has stopped the tray and motor. • Pick-up solenoid 3, 4 or 5 connector is loose. • Pick-up solenoid 3, 4 or 5 is blocked by an obstruction.
Remedy: 1. Replace the tray 3, 4 or 5 lift motor. 2. Replace the tray 3, 4 or 5 lift sensor. 3. Check or clear obstacles around pick-up solenoid 3, 4, or 5.
Description: Tray 4 (A4 LCT) feed error (G178/M078 only) One of the following conditions is detected in tray 3, 4 or 5 of the A4 LCT: The tray 3, 4 or 5 lift sensor is not activated for 10 s after the tray 3, 4 or 5 lift motor turned on. Upper limit is not detected within 10 s while the paper tray is lifting during paper feed. The tray 3, 4 or 5 lift sensor is already activated when tray 3, 4 or 5 is placed in the machine
Causes: • Poor connection or defective tray 3, 4 or 5 lift motor • Poor connection or defective tray 3, 4 or 5 lift sensor • Remaining paper or another obstruction has stopped the tray and motor. • Pick-up solenoid 3, 4 or 5 connector is loose. • Pick-up solenoid 3, 4 or 5 is blocked by an obstruction.
Remedy: 1. Replace the tray 3, 4 or 5 lift motor. 2. Replace the tray 3, 4 or 5 lift sensor. 3. Check or clear obstacles around pick-up solenoid 3, 4, or 5.
Description: Tray 5 (A4 LCT) feed error (G178/M078 only) One of the following conditions is detected in tray 3, 4 or 5 of the A4 LCT: The tray 3, 4 or 5 lift sensor is not activated for 10 s after the tray 3, 4 or 5 lift motor turned on. Upper limit is not detected within 10 s while the paper tray is lifting during paper feed. The tray 3, 4 or 5 lift sensor is already activated when tray 3, 4 or 5 is placed in the machine
Causes: • Poor connection or defective tray 3, 4 or 5 lift motor • Poor connection or defective tray 3, 4 or 5 lift sensor • Remaining paper or another obstruction has stopped the tray and motor. • Pick-up solenoid 3, 4 or 5 connector is loose. • Pick-up solenoid 3, 4 or 5 is blocked by an obstruction.
Remedy: 1. Replace the tray 3, 4 or 5 lift motor. 2. Replace the tray 3, 4 or 5 lift sensor. 3. Check or clear obstacles around pick-up solenoid 3, 4, or 5.
Description: Tray 3 (1st A3 LCT) feed error. One of the following conditions is detected in tray 3 or 4 of the 1st A3 LCT: The tray 3 or 4 lift sensor is not activated for 10 s after the tray 3 or 4 lift motor turned on. Upper limit is not detected within 10 s while the paper tray is lifting during paper feed. The tray 3 or 4 lift sensor is already activated when tray 3 or 4 is placed in the machine
Causes: • Poor connection or defective tray 3 or 4 lift motor • Poor connection or defective tray 3 or 4 lift sensor • Remaining paper or another obstruction has stopped the tray and motor. • Pick-up solenoid 3 or 4 connector is loose. • Pick-up solenoid 3 or 4 is blocked by an obstruction.
Remedy: 1. Replace the tray 3 or 4 lift motor. 2. Replace the tray 3 or 4 lift sensor. 3. Check or clear obstacles around pick-up solenoid 3 or 4.
Description: Tray 4 (1st A3 LCT) feed error. One of the following conditions is detected in tray 3 or 4 of the 1st A3 LCT: The tray 3 or 4 lift sensor is not activated for 10 s after the tray 3 or 4 lift motor turned on. Upper limit is not detected within 10 s while the paper tray is lifting during paper feed. The tray 3 or 4 lift sensor is already activated when tray 3 or 4 is placed in the machine
Causes: • Poor connection or defective tray 3 or 4 lift motor • Poor connection or defective tray 3 or 4 lift sensor • Remaining paper or another obstruction has stopped the tray and motor. • Pick-up solenoid 3 or 4 connector is loose. • Pick-up solenoid 3 or 4 is blocked by an obstruction.
Remedy: 1. Replace the tray 3 or 4 lift motor. 2. Replace the tray 3 or 4 lift sensor. 3. Check or clear obstacles around pick-up solenoid 3 or 4.
Nhận ưu đãi sớm nhất khi chương trình diễn ra
Đăng ký nhận bản tin
Việc cho phép sử dụng cookie sẽ giúp cải thiện trải nghiệm của bạn trên trang web này.
Chính sách cookie
Những cookie này là cần thiết để trang web hoạt động đúng cách.
Những cookie này giúp chúng tôi hiểu cách khách truy cập tương tác với trang web.
Những cookie này được sử dụng để cung cấp quảng cáo cá nhân hóa.