Thương hiệu phân phối chính hãng
Giỏ hàng

Mã lỗi Ricoh D135 MPC6502SP CH-C1 — Trang 51/63

Code: SC722-75

Description: Stacking Roller Drug Motor Error (D707) • When moving to the home position, home position was not detected within specified number of pulses (p0 pulses). (The first time: jam display, the second time: SC) • When moving from the home position, home position was still detected after specified number of pulses (p1 pulses). (The first time: jam display, the second time: SC)
Causes: • Overload due to staple jam or number of sheets exceeding the limit, etc. • Motor defective • Connecter disconnected • Home position sensor defective
Remedy: • Check the connections of the motor and home position sensor. • Replace the motor/home position sensor. • Replace the PCB.

Code: SC722-76

Description: Stacking Roller Motor Error (D707) Motor driver detected an open circuit or short-circuit. (SC from the first time)
Causes: • Motor defective • Connecter disconnected
Remedy: • Check motor connection. • Replace the motor. • Replace the PCB.

Code: SC725-01

Description: Downstream device communication error (D615) • Communication with the downstream device has established, but the device is not responding to the command sent out, even after being sent three times. • The port level of the downstream device does not become H level (break cancel) within specified time.
Causes: • Interface cable (downstream device side) connector disconnected or broken • PCB of downstream device defective • Controller PCB defective
Remedy: • Replace the interface cable. • Replace the PCB of downstream device. • Replace the controller board.

Code: SC725-12

Description: Reg. Roller Transport Motor Error (D615) • Motor driver detected an error. (SC from the first time)
Causes: • Overcurrent to the motor. • Motor drive overheat
Remedy: • Replace the controller board. • Replace the motor. • Replace the harness.

Code: SC725-13

Description: Dynamic Roller Transport Motor Error (D615) • Motor driver detected an error. (SC from the first time)
Causes: • Overcurrent to the motor. • Motor drive overheat
Remedy: • Replace the controller board. • Replace the motor. • Replace the harness.

Code: SC725-14

Description: Z-fold top tray exit motor error (D615) • Motor driver detected an error. (SC from the first time)
Causes: • Overcurrent to the motor. • Motor drive overheat
Remedy: • Replace the controller board. • Replace the motor. • Replace the harness.

Code: SC725-30

Description: Z-fold stopper 1 Motor error (D615) • When moving to the home position, home position was not detected within specified number of pulses (p0 pulses). (The first time: jam display, the second time: SC) • When moving from the home position, home position was still detected after specified number of pulses (p1 pulses). (The first time: jam display, the second time: SC) • Motor driver detected an error. (SC from the first time)
Causes: • Overcurrent to the motor. • Motor drive overheat • Connector disconnected
Remedy: • Replace the controller board. • Replace the motor. • Replace the harness. • Re-connect the connector. • Replace the sensor.

Code: SC725-31

Description: 2nd Stopper Motor Error (D615) • When moving to the home position, home position was not detected within specified number of pulses (p0 pulses). (The first time: jam display, the second time: SC) • When moving from the home position, home position was still detected after specified number of pulses (p1 pulses). (The first time: jam display, the second time: SC) • Motor driver detected an error. (SC from the first time)
Causes: • Overcurrent to the motor. • Motor drive overheat • Connector disconnected
Remedy: • Replace the controller board. • Replace the motor. • Replace the harness. • Re-connect the connector. • Replace the sensor.
Đăng ký nhận bản tin Đăng ký nhận bản tin Đăng ký nhận bản tin Đăng ký nhận bản tin
Đăng ký nhận bản tin
Nhận ưu đãi sớm nhất khi chương trình diễn ra

Đăng ký nhận bản tin

Việc cho phép sử dụng cookie sẽ giúp cải thiện trải nghiệm của bạn trên trang web này. Chính sách cookie