Thương hiệu phân phối chính hãng
Giỏ hàng

Mã lỗi Ricoh D136 MPC8002SP CH-C1 — Trang 53/63

Code: SC725-40

Description: 2nd Fold Motor Error (D615) • Motor driver detected an error. (SC from the first time)
Causes: • Overcurrent to the motor. • Motor drive overheat
Remedy: • Replace the controller board. • Replace the motor. • Replace the harness.

Code: SC725-41

Description: Crease Motor Error (D615) • Motor driver detected an error. (SC from the first time)
Causes: • Overcurrent to the motor. • Motor drive overheat
Remedy: • Replace the controller board. • Replace the motor. • Replace the harness.

Code: SC725-71

Description: Horizontal Transport Motor Error (D615) • Motor driver detected an error. (SC from the first time)
Causes: • Overcurrent to the motor. • Motor drive overheat
Remedy: • Replace the controller board. • Replace the motor. • Replace the harness.

Code: SC725-72

Description: Horizontal exit motor error (D615) • Motor driver detected an error. (SC from the first time)
Causes: • Overcurrent to the motor. • Motor drive overheat
Remedy: • Replace the controller board. • Replace the motor. • Replace the harness.

Code: SC725-73

Description: Horizontal exit motor error (D615) • Motor driver detected an error. (SC from the first time)
Causes: • Overcurrent to the motor. • Motor drive overheat
Remedy: • Replace the controller board. • Replace the motor. • Replace the harness.

Code: SC725-74

Description: Entrance JG Motor Error (D615) • When moving to the home position, home position was not detected within specified number of pulses (p0 pulses). (The first time: jam display, the second time: SC) • When moving from the home position, home position was still detected after specified number of pulses (p1 pulses). (The first time: jam display, the second time: SC) • Motor driver detected an error. (SC from the first time)
Causes: • Overcurrent to the motor. • Motor drive overheat • Connector disconnected
Remedy: • Replace the controller board. • Replace the motor. • Replace the harness. • Re-connect the connector. • Replace the sensor.

Code: SC740-01

Description: Downstream device communication error (D712) • Communication with the downstream device has established, but the device is not responding to the command sent out, even after being sent three times. • The port level of the downstream device does not become H level (break cancel) within specified time.
Causes: • Interface cable (between inserter and downstream device) connector disconnected or broken • PCB (of inserter or downstream device) defective
Remedy: • Reconnect or replace the interface cable (between inserter and downstream device) connector disconnected or broken • Replace the PCB.

Code: SC740-10

Description: Bottom Plate Lift Motor Error (D711) • The lift motor rotates in the ascending direction but the upper limit sensor does not detect within specified time (t0sec). (The first time: jam display, the second time: SC) • The lift motor rotates in the descending direction but the lower limit sensor does not detect within specified time (t0sec). (The first time: jam display, the second time: SC)
Causes: • Motor defective • Connecter disconnected • Overload • Upper limit sensor defective • Lower limit sensor defective
Remedy: • Check the motor and upper limit sensor. • Check the lower limit sensor. • Replace the motor/upper limit sensor./lower limit sensor. • Replace the PCB.
Đăng ký nhận bản tin Đăng ký nhận bản tin Đăng ký nhận bản tin Đăng ký nhận bản tin
Đăng ký nhận bản tin
Nhận ưu đãi sớm nhất khi chương trình diễn ra

Đăng ký nhận bản tin

Việc cho phép sử dụng cookie sẽ giúp cải thiện trải nghiệm của bạn trên trang web này. Chính sách cookie