Thương hiệu phân phối chính hãng
Giỏ hàng

Mã lỗi Ricoh D193 MPC401SRSP Z-C2

Code: 101

Description: LED lamp error The peak white level is less or more than 64/255 digits (8 bits) when scanning the shading plate.
Causes: • LED board defective • IDB defective • Harness connection between LED board and IDB disconnected • Standard white plate dirty • Scanner mirror or scanner lens out of position or dirty • SBU, IPU or BCU defective
Remedy: • Check and clean the scanner mirror(s) and scanner lens. • Check and clean the shading plate. • Check the cable connection between the LED board and IDB. • Replace the LED board. • Replace the IDB. • Replace the SBU, IPU or BCU.

Code: 120

Description: Scanner home position error 1 The scanner home position sensor does not detect the "OFF" condition during operation.
Causes: • Scanner motor driver defective • Scanner motor defective • Harness between IPU and scanner motor disconnected • Scanner HP sensor defective • Harness between IPU and HP sensor disconnected • IPU or BCU defective
Remedy: • Check the cable connections (IPU to scanner motor and IPU and scanner HP sensor). • Replace the scanner motor. • Replace the HP sensor. • Replace the IPU or BCU.

Code: 121

Description: Scanner home position error 2 The scanner home position sensor does not detect the "ON" condition during operation.
Causes: • Scanner motor driver defective • Scanner motor defective • Harness between IPU and scanner motor disconnected • Scanner HP sensor defective • Harness between IPU and HP sensor disconnected • IPU or BCU defective
Remedy: • Check the cable connections (IPU to scanner motor and IPU and scanner HP sensor). • Replace the scanner motor. • Replace the HP sensor. • Replace the IPU or BCU.

Code: 141

Description: Black level detection error The black level cannot be adjusted within the target value during the zero clamp.
Causes: • Harness disconnected • IPU defective • SBU defective
Remedy: • Check the cable connection • Replace the IPU. • Replace the SBU.

Code: 142

Description: White level detection error The white level cannot be adjusted within the target during auto gain control.
Causes: • Dirty exposure glass or optics section • Harness between LED lamp and IDB disconnected • SBU defective • LED lamp defective • IDB defective • IPU defective
Remedy: • Clean the exposure glass, white plate, mirrors, and lens. • Check if the LED lamp is lit during initialization. • Check the harness connections (LED board to IDB, IDB to IPU and SBU to IPU). • Replace the LED board. • Replace the IDB. • Replace the SBU. • Replace the IPU.

Code: 144

Description: SBU communication error The SBU connection cannot be detected at power on or recovery from the energy save mode.
Causes: • Defective SBU • Defective harness • Defective detection port on the IPU • Defective detection port on the BCU
Remedy: • Replace the harness. • Replace the SBU. • Replace the IPU. • Replace the BCU.

Code: 161-001

Description: IPU error 001 The error result of self-diagnostic by the ASIC on the IPU is detected.
Causes: • Defective IPU • Defective connection between IPU and SBU
Remedy: 1. Check the connection between IPU and SBU. 2. Replace the IPU.

Code: 161-002

Description: IPU error. The machine detects an error during an access to the Ri.
Causes: • Defective IPU
Remedy: Replace the IPU.
Đăng ký nhận bản tin Đăng ký nhận bản tin Đăng ký nhận bản tin Đăng ký nhận bản tin
Đăng ký nhận bản tin
Nhận ưu đãi sớm nhất khi chương trình diễn ra

Đăng ký nhận bản tin

Việc cho phép sử dụng cookie sẽ giúp cải thiện trải nghiệm của bạn trên trang web này. Chính sách cookie