Thương hiệu phân phối chính hãng
Giỏ hàng

Mã lỗi Ricoh D199 MP3354 Cor-C1 — Trang 11/40

Code: SC544-02

Description: Fusing High Temperature Detection (hardware) (Non-Contact thermistor High Temperature Error) In the event of an error
Causes: • Triac defective (short-circuit) • Engine controller defective • Heating central thermopile defective • Fusing control software: out of control
Remedy: • Attach the new fusing unit, then run SP-5-810-002. • If the triac is defective, replace the AC power supply board. • If necessary, replace the BCU or the Fusing central NC sensor.

Code: SC545-01

Description: Fusing Central Heater Continuously Heat After waiting for full power for more than specified seconds continuously, not detected for specified seconds. • Definition of heater full power Continuously heating rate set point (maximum heating rate) • Measurement start point After reload (after heater extinguished, after rotation complete) below the standby temperature (target temperature), measurement starts after a heater heat-up request is issued. • Measurement stop condition Rotation started due to a print signal during measurement or other. • Maximum heat-up Duty (SP interlinked value) 0% is excluded.
Causes: • Thermistor deformation/float • Heater disconnection • After excessive temperature rise prevention unit operates
Remedy: • Replace the thermistor. • Replace the fusing lamp. • Replace the fusing unit.

Code: SC545-05

Description: Fusing Central Heater Continuously Heat (Low Voltage)
Causes: Low Voltage
Remedy:

Code: SC547-01

Description: Zero cross Error (relay-contact soldering) In the event of an error
Causes: • Fusing relay defective (contact soldering) • Fusing relay drive circuit fault
Remedy: • Turn the main power supply switch OFF/ON • If the fusing relay is damaged, replace the PSU. • Check the connection between PSU and control board, and replace harness and board if necessary.

Code: SC547-02

Description: Zero cross Error (relay contact fault) In the event of an error
Causes: • Fusing relay damage (contact open) • Fusing relay drive circuit fault • PSU fuse (24VS) blowout
Remedy: • Turn the main power supply switch OFF/ON. • If the fusing relay is damaged, replace the PSU. • Check the connection between PSU and control board, and replace harness and board if necessary. • If the PSU fuse (24VS) blows out, replace the fuse.

Code: SC547-03

Description: Zero cross Error (low-frequency error) In the event of an error
Causes: Frequency instability of commercial power line
Remedy: • Turn the main power supply switch OFF/ON. • Check the power source. • Check the connection between PSU and control board, and replace harness and board if necessary.

Code: SC551-01

Description: Fusing Edge Thermopile Disconnection When the fusing edge thermopile detects a predetermined temperature or less for specified seconds consecutively.
Causes: • Thermopile disconnection • Connector disconnected
Remedy: • Replace the thermopile. • Reset the connector. • Replace the connector. • Replace the fusing unit.

Code: SC551-02

Description: Edge NC Sensor Disconnection 3ED - 3FF (FB voltage: 3.243V-3.300V) is detected for specified seconds continuously (NC sensor center: detection & compensation NC sensor edge: detection & compensation). Detection period: 100 ms, detection frequency: 10 times or more.
Causes: • NC sensor disconnection • Connector disconnected
Remedy: • Replace the NC sensor. • Reset the connector. • Replace the connector. • Replace the fusing unit.
Đăng ký nhận bản tin Đăng ký nhận bản tin Đăng ký nhận bản tin Đăng ký nhận bản tin
Đăng ký nhận bản tin
Nhận ưu đãi sớm nhất khi chương trình diễn ra

Đăng ký nhận bản tin

Việc cho phép sử dụng cookie sẽ giúp cải thiện trải nghiệm của bạn trên trang web này. Chính sách cookie