Thương hiệu phân phối chính hãng
Giỏ hàng

Mã lỗi Ricoh M036 MPC232DN PE-P1E

Code: 195

Description: Serial Number Error
The serial number stored in the memory (EGB) is not correct.
Causes: EEPROM defective. EGB replaced without original EEPROM.
Remedy: 1. Check the serial number. 2. If the stored serial number is incorrect, contact your supervisor.

Code: 300

Description: High voltage power output error
The measured voltage is not correct when the EGB measures each charge output (charge, development, image transfer belt unit, and transfer unit).
Causes: Disconnected or defective high voltage harness. Defective high voltage power supply. Defective EGB.
Remedy: 1. Check or replace the harnesses. 2. Replace the high voltage power supply board 3. Replace the EGB.

Code: 396

Description: Black drum motor error
The LOCK signal error is detected when the EGB monitors the black drum motor state. (This monitoring is done immediately after power-on, when the motor starts rotating, and immediately after the motor stops.)
Causes: Disconnected or defective motor harness. Motor slips due to excessive load.
Remedy: 1. Check the harness from the black drum motor. Replace it if necessary.

Code: 397

Description: Color drum motor error
The LOCK signal error is detected when the EGB monitors the color drum motor state. (This monitoring is done immediately after power-on, when the motor starts rotating, and immediately after the motor stops.)
Causes: Disconnected or defective motor harness. Motor slips due to excessive load.
Remedy: 1. Check the harness from the color drum motor. Replace it if necessary.

Code: 445

Description: ITB (Image Transfer Belt) Unit Error
Home Position Error The ITB contact sensor does not detect the home position of the ITB for 5 seconds after the ITB unit initialization has been done. ITB (Image Transfer Belt) Unit: Contact Position Error The ITB contact sensor does not detect the contact position of the ITB for 5 seconds after the ITB unit has moved to the contact position. ITB (Image Transfer Belt) Unit: No-contact Position Error The ITB contact sensor does not detect the home position of the ITB for 5 seconds after the ITB unit has moved to no-contact position.
Causes: Defective ITB contact motor. Defective ITB contact sensor. Defective ITB unit.
Remedy: 1. Replace the ITB contact motor. 2. Replace the ITB contact sensor. 3. Replace the ITB unit.

Code: 480

Description: Agitator Motor Error
The agitator motor error is detected twice for 10 msec during the initialization at power-on or after the cover is closed.
Causes: Disconnected or defective harness. Defective agitator motor.
Remedy: 1. Check or replace the harness. 2. Replace the agitator motor.

Code: 490

Description: ITB (Image Transfer Belt) Unit Set Error
The TM sensor does not detect the reflection from the ITB.
Causes: No ITB unit in the machine. Dirty TM sensor.
Remedy: 1. Check the installation of the ITB unit. 2. Clean the TM sensor.

Code: 500

Description: Transport/Fusing Motor Error
The LOCK signal error is detected when the EGB monitors the transport/fusing motor state. (This monitoring is done immediately after power-on, when the motor starts rotating, and immediately after the motor stops.)
Causes: Disconnected or defective motor harness. Motor slips due to excessive load.
Remedy: 1. Check the harness from the transport/fusing motor. Replace it if necessary.
Đăng ký nhận bản tin Đăng ký nhận bản tin Đăng ký nhận bản tin Đăng ký nhận bản tin
Đăng ký nhận bản tin
Nhận ưu đãi sớm nhất khi chương trình diễn ra

Đăng ký nhận bản tin

Việc cho phép sử dụng cookie sẽ giúp cải thiện trải nghiệm của bạn trên trang web này. Chính sách cookie