Thương hiệu phân phối chính hãng
Giỏ hàng

Mã lỗi Ricoh M040 SPC311N

Code: 195

Description: Serial Number Error
The serial number stored in the memory (EGB) is not correct.
Causes: EEPROM defective. EGB replaced without original EEPROM.
Remedy: 1. Check the serial number. 2. If the stored serial number is incorrect, contact your supervisor. 3. Appendix: Troubleshooting Guide 16

Code: 202

Description: Polygon motor error 1: ON timeout
The polygon mirror motor does not reach the targeted operating speed within 5 sec. after turning on or changing speed
Causes: Polygon motor/driver board harness loose or disconnected. Polygon motor/driver board defective. Laser optics unit defective. IPU (EGB) defective.
Remedy: 1. Replace the interface harness of the laser optics unit. 2. Replace the laser optics unit. 3. Replace the EGB (Engine Board).

Code: 203

Description: Polygon motor error 2: OFF timeout
The polygon mirror motor does not leave the READY status within 3 sec. after the polygon motor switched off.
Causes: Polygon motor/driver board harness loose or disconnected. Polygon motor/driver board defective. Laser optics unit defective. IPU (EGB) defective.
Remedy: 1. Replace the interface harness of the laser optics unit. 2. Replace the laser optics unit. 3. Replace the EGB (Engine Board).

Code: 204

Description: Polygon motor error 3: XSCRDY signal error
The SCRDY_N signal remains HIGH for 200 ms while the LD unit is firing.
Causes: Polygon motor/driver board harness loose or disconnected. Polygon motor/driver board defective. Laser optics unit defective. IPU (EGB) defective.
Remedy: 1. Replace the interface harness of the laser optics unit. 2. Replace the laser optics unit. 3. Replace the EGB (Engine Board).

Code: 220

Description: Laser Synchronizing Detection Error: [K]/[Y]
The laser synchronizing detection signal for LDB [K]/[Y] is not output after the LDB unit has turned on while the polygon motor is rotating normally.
Causes: Disconnected cable from the laser synchronizing detection unit or defective connection. Defective laser synchronizing detector. Defective LDB. Defective EGB.
Remedy: 1. Check the connectors. 2. Replace the laser optics unit. 3. Replace the EGB.

Code: 222

Description: Laser Synchronizing Detection Error: [M]/[C]
The laser synchronizing detection signal for LDB [M]/[C] is not output after the LDB unit has turned on while the polygon motor is rotating normally.
Causes: Disconnected cable from the laser synchronizing detection unit or defective connection. Defective laser synchronizing detector. Defective LDB. Defective EGB.
Remedy: 1. Check the connectors. 2. Replace the laser optics unit. 3. Replace the EGB.

Code: 240

Description: LD error
The IPU (EGB) detects a problem at the LD unit.
Causes: Worn-out LD. Disconnected or broken harness of the LD.
Remedy: 1. Replace the laser optics unit.

Code: 300

Description: High voltage power output error
The measured voltage is not correct when the EGB measures each charge output (charge, development, image transfer belt unit, and transfer unit).
Causes: Disconnected or defective high voltage harness. Defective high voltage power supply. Defective EGB.
Remedy: 1. Check or replace the harnesses. 2. Replace the high voltage power supply board 3. Replace the EGB. 4. Replace the AIOs.
Đăng ký nhận bản tin Đăng ký nhận bản tin Đăng ký nhận bản tin Đăng ký nhận bản tin
Đăng ký nhận bản tin
Nhận ưu đãi sớm nhất khi chương trình diễn ra

Đăng ký nhận bản tin

Việc cho phép sử dụng cookie sẽ giúp cải thiện trải nghiệm của bạn trên trang web này. Chính sách cookie