Thương hiệu phân phối chính hãng
Giỏ hàng

Mã lỗi Ricoh M078 Aficio Pro C720 AGL-P1 — Trang 36/85

Code: 562

Description: Heating roller warm-up error 3 • The heating roller temperature does not reach the ready temperature for 850 seconds after the heating roller lamp on. • The heating roller temperature does not reach 100°C for 400 seconds after the heating roller lamp on.
Causes: • Defective thermistor • Related SC code: SC 542, SC552
Remedy: 1. Check if the heating roller thermistor is firmly connected. 2. Replace the heating roller thermistor.

Code: 563

Description: Heating roller overheat 2 (software error) The detected heating roller temperature (end) stays at 225°C or more for 10 seconds.
Causes: • Defective AC drive board • Defective IOB 2 • Defective BCU • Related SC code: SC 543, SC553
Remedy: 1. Do SP5810 to cancel the SC fusing code. 2. Replace the AC drive board. 3. Replace the IOB 2. 4. Replace the BCU.

Code: 565

Description: Heating roller fusing lamp on error After fusing belt reached warm-up temperature, the heating roller fusing lamp remained on for 300 sec. while the hot roller was not rotating.
Causes: • Thermistor damaged, or out of position • Fusing lamp disconnected, broken
Remedy: 1. Do SP5810 to cancel the SC fusing code. 2. Replace the heating roller thermistor.

Code: 569

Description: Pressure roller lift error Pressure roller lift motor not operating correctly. (No signal to indicate completion of operation.)
Causes: • Pressure roller lift motor defective • Pressure roller lift sensor connection loose, broken, damaged Pressure roller lift motor blocked by an obstruction
Remedy: 1. Replace the pressure roller lift motor. 2. Replace the pressure roller lift sensor.

Code: 584

Description: De-curler unit HP detection error The de-curler unit HP sensor does not detect a home position for 6 seconds after the de-curler unit has tried to search for its home position.
Causes: • De-curler unit HP sensor connection loose or disconnected • De-curler unit HP sensor defective
Remedy: 1. Check the connection of the de-curler unit HP sensor. 2. Replace the de-curler unit HP sensor.

Code: 585

Description: Double-feed led adjustment error The calibration of the double-feed LED for the paper type failed to reach the target voltage.
Causes: • Double-feed sensor: LED and receptor dirty • Sensor: LED and receptor connectors loose, broken, defective
Remedy: 1. Check the connection of the double-feed sensor: LED and Receptor. 2. Replace the double-feed sensor: LED and Receptor.

Code: 586

Description: De-curler limit sensor error • The de-curler unit moves beyond the regulated range. • The de-curler limit sensor does not detect any signal.
Causes: • De-curler unit HP sensor connection loose or disconnected • De-curler unit HP sensor defective • De-curler unit limit sensor connection loose or disconnected • De-curler unit limit sensor defective
Remedy: 1. Check the connection of the de-curler unit HP sensor. 2. Replace the de-curler unit HP sensor. 3. Check the connection of the de-curler unit limit sensor. 4. Replace the de-curler unit limit sensor.

Code: 590-001, 590-002

Description: -001 C Paper feed motor 1 error -002 C Paper feed motor 2 error. The machine detects a short or open signal of the coil in paper feed motor 1 or 2.
Causes: • Harness from IOB 2 to this motor short, broken or disconnected • Coil in one of these motors short or open
Remedy: 1. Check the harness connection. 2. Replace the harness. 3. Replace paper feed motor 1 or 2.
Đăng ký nhận bản tin Đăng ký nhận bản tin Đăng ký nhận bản tin Đăng ký nhận bản tin
Đăng ký nhận bản tin
Nhận ưu đãi sớm nhất khi chương trình diễn ra

Đăng ký nhận bản tin

Việc cho phép sử dụng cookie sẽ giúp cải thiện trải nghiệm của bạn trên trang web này. Chính sách cookie