Thương hiệu phân phối chính hãng
Giỏ hàng

Mã lỗi Samsung ML6510ND — Trang 12/13

Code: M3-2130

Display: Output bin full. Remove printed paper
Description: The paper is full on the output bin. - The outbin full sensor is defective.
Remedy: 1. Remove the paper on the output bin. 2. Check if the sensor connector is connected properly.

Code: S1-2111

Display: Video System Failure: #S1-2111 Turn off then on
Description: The memory module is defective.
Remedy: 1. Check if the momory module in the main board is installed. Remove and reinstall it. 2. If the problem persists, replace the main board.

Code: S2-4110

Display: Door is open. Close it
Description: The top cover is closed but error message is not disappeared. 1. Harness connection error. 2. Micro Switch defect.
Remedy: 1. Check if the harness (Picture(1)-..) is normal. 2. Check if the harness is the connected to the Relay connector (Picture(1)-..) properly. 3. Check if the connector CN9 (Picture(1)-..) on the engine board is connected properly. 4. Open the cover of the OPE panel. Check if the UI message is changed when pushing the micro switch (Picture(2)-..). 5. If the micro switch is defective, replace it.

Code: S2-4610

Display: Rear Door is open. Close it
Description: The rear cover is closed but error message is not disappeared. 1. The rear cover is closed perfectly. 2. Relay connector pin is defective. 3. Harness connection error.
Remedy: 1. Check if the rear cover is closed perfectly. 2. Check the Relay connector Pin If it is defective, replace it. 3. Check the Relay connector if it is defective, replace it. 4. Remove the left cover. Check the harness.. between the Joint board and Relay connector. 5. Check if the harness is connected to the connector properly.

Code: S6-3123

Display: This IP address conflicts with that of other system
Description: IP address conflicts with that of other system.
Remedy: Change the machine’s IP address.

Code: S6-3128

Display: 802.1x Network Error Contact the Admin.
Description: Can not get the authentication from server after setting up to 802.1x on SWS. Can not access to network.
Remedy: Check if the Authentication method is selected properly. Check if the User Name/Password is entered properly.

Code: U1-2115

Display: Fuser Unit Failure: #U1-2115. Turn off then on
Description: The photo sensor is defective or some part is not assembled properly.
Remedy: 1. Remove the Rear Cover and Duplex Unit. Remove the fuser unit after removing 4 screws. 2. Remove the GUIDE-EXIT LOWER. To remove it, fi rst, push and release the green lever to the direction of arrow. Then, lift and pull it. 3. To remove the COVER-DUPELX, a. Remove 1 screw. Lift up the COVER-DUPLEX PATH to the direction of arrow slightly. b. Release the both hooks with the tweezers or (-) driver. 4. Remove the COVER-LEFT after removing 2 screws. Remove the COVER-RIGHT after removing 2 screws. 5. Check if the photo sensor connector from the COVER-RIGHT is connected properly. 6. Check if the left/right CAM and the ENCORDER are assembled properly. 7. If there is no problem for above steps, reassemble the fuser unit and turn the machine on. 8. If the error persists, download the fi rmware again. 9. If the problem persists, replace the fuser unit with new one. 10. If the problem persists, replace the engine board.

Code: U1-2117

Display: Fuser Unit Failure: #U1-2117. Turn off then on
Description: The photo sensor is defective or some part is not assembled properly.
Remedy: 1. Remove the Rear Cover and Duplex Unit. Remove the fuser unit after removing 4 screws. 2. Remove the GUIDE-EXIT LOWER. To remove it, fi rst, push and release the green lever to the direction of arrow. Then, lift and pull it. 3. To remove the COVER-DUPELX, a. Remove 1 screw. Lift up the COVER-DUPLEX PATH to the direction of arrow slightly. b. Release the both hooks with the tweezers or (-) driver. 4. Check if the fuser is assembled and fuser connector is connected properly. 5. If there is no problem for above steps, reassemble the fuser unit and turn the machine on. 6. If the error persists, execute the Memory Clear. (Note: Perform a backup first if necessary.) 7. If the problem persists, replace the fuser unit with new one. 8. If the problem persists, replace the engine board.
Đăng ký nhận bản tin Đăng ký nhận bản tin Đăng ký nhận bản tin Đăng ký nhận bản tin
Đăng ký nhận bản tin
Nhận ưu đãi sớm nhất khi chương trình diễn ra

Đăng ký nhận bản tin

Việc cho phép sử dụng cookie sẽ giúp cải thiện trải nghiệm của bạn trên trang web này. Chính sách cookie