Thương hiệu phân phối chính hãng
Giỏ hàng

Mã lỗi Samsung SLM3870FW — Trang 6/9

Code: M1-5112

Display: Paper empty in tray 1 / Paper is empty in tray 1. Load paper All Tray Empty / Paper is empty in all tray. Load paper
Description: There is no paper in the tray1. / Actuator-Paper Empty or photo sensor is defective.
Remedy: 1) Load the paper in the tray1. If the problem persists, check the followings after turning the machine off. 2) If the Actuator-Paper Empty(JC66-02762A) is defective, replace it. (Refer to 3.3.21) 3) If the photo sensor(0604-001393) is defective, replace it. Check if the connector is connected properly. 4) If the problem persists, replace the main board.

Code: M1-5113

Display: Paper empty in tray 1 / Paper is empty in tray 1. Load paper All Tray Empty / Paper is empty in all tray. Load paper
Description: There is no paper in the tray1. / Actuator-Paper Empty or photo sensor is defective.
Remedy: 1) Load the paper in the tray1. If the problem persists, check the followings after turning the machine off. 2) If the Actuator-Paper Empty(JC66-02762A) is defective, replace it. (Refer to 3.3.21) 3) If the photo sensor(0604-001393) is defective, replace it. Check if the connector is connected properly. 4) If the problem persists, replace the main board.

Code: M1-5120

Display: Paper empty in tray 1 / Paper is empty in tray 1. Load paper All Tray Empty / Paper is empty in all tray. Load paper
Description: There is no paper in the tray1. / Actuator-Paper Empty or photo sensor is defective.
Remedy: 1) Load the paper in the tray1. If the problem persists, check the followings after turning the machine off. 2) If the Actuator-Paper Empty(JC66-02762A) is defective, replace it. (Refer to 3.3.21) 3) If the photo sensor(0604-001393) is defective, replace it. Check if the connector is connected properly. 4) If the problem persists, replace the main board.

Code: M1-5612

Display: Paper empty in MP / Paper is empty in MP tray. Load paper
Description: There is no paper in the MP tray (or Manual Feeder). / Actuator-Paper Empty or photo sensor is defective.
Remedy: 1) Load the paper in the tray1. If the problem persists, check the followings after turning the machine off. 2) If the Actuator-Paper Empty(JC66-02762A) is defective, replace it. (Refer to 3.3.21) 3) If the photo sensor(0604-001393) is defective, replace it. Check if the connector is connected properly. 4) If the problem persists, replace the main board.

Code: M1-5712

Display: Paper Empty in manual feeder / Paper is empty in manual feeder. Load paper
Description: There is no paper in the MP tray (or Manual Feeder). / Actuator-Paper Empty or photo sensor is defective
Remedy: 1) Load the paper in the tray1. If the problem persists, check the followings after turning the machine off. 2) If the Actuator-Paper Empty(JC66-02762A) is defective, replace it. (Refer to 3.3.21) 3) If the photo sensor(0604-001393) is defective, replace it. Check if the connector is connected properly. 4) If the problem persists, replace the main board.

Code: M2-1110

Display: Jam inside machine
Description: A paper jam was detected at the feed sensor.
Remedy: 1) Remove the jammed paper. (Refer to 4.1.3) If the error persists, check the followings. 2) Check if the feed sensor connector is connected properly. 3) Check if the Regi roller is contaminated or worn out. If yes, replace it. 4) Check if there is any obstacles or contamination in the paper path. If yes, clean or remove it.

Code: M2-2210

Display: Jam inside of duplex
Description: A paper jam was detected in the bottom of duplex.
Remedy: 1) Remove the jammed paper. 2) Remove the contamination or obstacles in the paper path. 3) If this jam error occur continually, replace the duplex unit.

Code: M3-1110

Display: Jam in exit area
Description: A paper jam was detected in the exit area.
Remedy: 1) Remove the jammed paper. 2) Check if there is any obstacles or contamination in the paper path. If yes, clean or remove it. 3) Check if the exit roller rubber is worn out. Replace the exit roller(JC93-00323A). 4) Check if the exit sensor connector is connected properly. If the connection is OK, replace the exit sensor.
Đăng ký nhận bản tin Đăng ký nhận bản tin Đăng ký nhận bản tin Đăng ký nhận bản tin
Đăng ký nhận bản tin
Nhận ưu đãi sớm nhất khi chương trình diễn ra

Đăng ký nhận bản tin

Việc cho phép sử dụng cookie sẽ giúp cải thiện trải nghiệm của bạn trên trang web này. Chính sách cookie