Thương hiệu phân phối chính hãng
Giỏ hàng

Mã lỗi Sharp AR405 — Trang 7/11

Code: H3 01, H3 HL2

Description: Heat roller high temperature detection. The fusing temperature is over 241.5°C (less than 1.3-V input voltage is detected.)
Causes: Thermister defective Control PWB defective Improper connection of fusing unit connector AC power supply defective
Remedy: Check heater lamp operation with SIM5-2. If lamp blinks properly: Check thermister and its harness. Check thermister input circuit of control PWB. If lamp lights and stays lit: Check lamp control circuits of AC PWB and control PWB. Clear the trouble with SIM14.

Code: H4 00, H4 HL1

Description: Heat roller low temperature detection. The temperature does not reach the preset value within the specified time (3 min. in usual modes; 5 min. in curl correction mode.) after the power relay is turned on.
Causes: Thermister defective Heater lamp defective Control PWB defective Thermostat defective AC power supply defective Interlock switch defective
Remedy: Check heater lamp for blinking with SIM5-2. If lamp blinks properly: Check thermister and its harness. Check thermister input circuit of control PWB. If lamp does not light: Check heater lamp for broken wire and thermostat for operation. Check interlock switch. Check lamp control circuit of AC PWB and control PWB. Clear the trouble with SIM14.

Code: H4 01, H4 HL2

Description: Heat roller low temperature detection. The temperature does not reach the preset value within the specified time (3 min. in usual modes; 5 min. in curl correction mode.) after the power relay is turned on.
Causes: Thermister defective Heater lamp defective Control PWB defective Thermostat defective AC power supply defective Interlock switch defective
Remedy: Check heater lamp for blinking with SIM5-2. If lamp blinks properly: Check thermister and its harness. Check thermister input circuit of control PWB. If lamp does not light: Check heater lamp for broken wire and thermostat for operation. Check interlock switch. Check lamp control circuit of AC PWB and control PWB. Clear the trouble with SIM14.

Code: H5 01

Description: 3 continuous POD1 not-reaching JAM detection. 3 continuous POD1 not-reaching JAM detection
Causes: Check that the fusing JAM is completely cancelled. (Jam paper may be remained.) POD1 sensor trouble or improper harness connection Improper installation of the fusing harness.
Remedy: Check JAM paper in the fusing section. (Winding, etc.) Check POD1 sensor harness. Check the fusing unit installation. Cancel the trouble with SIM 14.

Code: H5 02

Description: Fusing thermistor abnormality. Fusing thermistor temperature transient abnormality (Paper winding)
Causes: Paper winding to fusing roller Fusing pawl abnormality Fusing unit installation abnormality
Remedy: Check for jam (winding) paper in the fusing section. Check for installation of the fusing unit. Check the fusing pawl. Cancel the trouble with SIM 14.

Code: L1 00

Description: Scanner feed trouble. Scanner feed is not finished within the specified time. (timer is change by magnification)
Causes: Mirror unit defective Scanner wire disconnected
Remedy: Check scanning operation with SIM1-1.

Code: L3 00

Description: Scanner return trouble. Scanner return is not finished within the specified time. (timer is change by magnification)
Causes: Mirror unit defective Scanner wire disconnected
Remedy: Check scanning operation with SIM1-1.

Code: L4 01

Description: Main motor lock detection. Motor lock signal is detected for 1.5 seconds during main motor rotation
Causes: Main motor defective Improper connection of harness between PCU PWB and main motor Control circuit defective
Remedy: Check main motor operation with SIM25-1. Check harness and connector between PCU PWB and main motor.
Đăng ký nhận bản tin Đăng ký nhận bản tin Đăng ký nhận bản tin Đăng ký nhận bản tin
Đăng ký nhận bản tin
Nhận ưu đãi sớm nhất khi chương trình diễn ra

Đăng ký nhận bản tin

Việc cho phép sử dụng cookie sẽ giúp cải thiện trải nghiệm của bạn trên trang web này. Chính sách cookie