Thương hiệu phân phối chính hãng
Giỏ hàng

Mã lỗi Sharp ARC100 — Trang 11/15

Code: L4 5

Description: Developing motor trouble (COLOR)
Causes: The motor lock signal is detected for 1.5sec or more when the developing motor is ON.
Remedy: Case 1 Trouble position/cause Developing motor trouble Remedy (Check) Check the developing motor operation (SIM 25-1). (Repair) Replace the developing motor. / Power Source-ON (After-work) Note Case 2 Trouble position/cause Developing mechanism section trouble Remedy (Check) Check the loads of the developing mechanism section. (Repair) Repair or replace the parts in the developing mechanism section. / Power Source-ON (After-work) Note Case 3 Trouble position/cause PCU MAIN PWB trouble Remedy (Check) (Repair) Replace the PCU MAIN PWB. / Power Source-ON (After-work) Re-enter setup values and adjustment values. (Install the EEPROM of the defective PCU MAIN PWB to a new PCU MAIN PWB.) Note Case 4 Trouble position/cause Developing motor power line trouble Remedy (Check) Check the fuse (F707). (Repair) Replace the fuse (F707). / Power Source-ON

Code: L4 6

Description: Transfer belt lift trouble
Causes: The transfer unit home position sensor (BLLD) ON/OFF is not detected (kept ON or OFF) when the transfer unit is lifted up and down.
Remedy: Case 1 Trouble position/cause Transfer belt lift motor trouble Remedy (Check) Check the transfer belt lift motor. (SIM 6-1) (Repair) Replace the transfer belt lift motor. / Power Source-ON (After-work) Note Case 2 Trouble position/cause Transfer unit home position sensor (BLUD) trouble Remedy (Check) Check the transfer unit home position sensor (BLUD) operation. (SIM 30-1) (Repair) Replace the transfer unit home position sensor (BLUD). / Power Source-ON Case 3 Trouble position/cause Transfer unit lift mechanism section trouble Remedy (Check) Check the transfer unit lift mechanism section. (Repair) Repair the transfer unit lift mechanism or replace the parts. / Power Source-ON (After-work) Note Case 4 Trouble position/cause PCU SUB PWB trouble Remedy (Check) PCU SUB PWB transfer lift motor circuit check. (Repair) PCU SUB PWB replacement / Power Source-ON

Code: L6 10

Description: Scanner (writing) motor lock detection (BLACK)
Causes: Scanner (writing) unit (LSU) polygon motor lock signal detection trouble (The lock signal is not detected for 10 sec after turning on the polygon motor.)
Remedy: Case 1 Trouble position/cause Scanner (writing) unit (LSU) trouble Remedy (Check) Scanner (writing) unit (LSU) operation check (SIM 61-1) (Repair) Replace the scanner (writing) unit (LSU). / Power Source-ON (After-work) Adjust ADJM7/ADJM9/ADJM10 Note Case 2 Trouble position/cause ICU MAIN PWB trouble Remedy (Check) (Repair) ICUMAIN PWB replacement / Power Source-ON (After-work) Adjust ADJM9/M10/M12/M13/M14/M15/M17. / Re-enter setup values and adjustment values. (Install the EEPROM of the defective ICU MAIN PWB to a new ICU MAIN PWB.)

Code: L6 11

Description: Scanner (writing) motor lock detection (CYAN)
Causes: Scanner (writing) unit (LSU) polygon motor lock signal detection trouble (The lock signal is not detected for 10 sec after turning on the polygon motor.)
Remedy: Case 1 Trouble position/cause Scanner (writing) unit (LSU) trouble Remedy (Check) Scanner (writing) unit (LSU) operation check (SIM 61-1) (Repair) Replace the scanner (writing) unit (LSU). / Power Source-ON (After-work) Adjust ADJM7/ADJM9/ADJM10 Note Case 2 Trouble position/cause ICU MAIN PWB trouble Remedy (Check) (Repair) ICUMAIN PWB replacement / Power Source-ON (After-work) Adjust ADJM9/M10/M12/M13/M14/M15/M17. / Re-enter setup values and adjustment values. (Install the EEPROM of the defective ICU MAIN PWB to a new ICU MAIN PWB.)

Code: L6 12

Description: Scanner (writing) motor lock detection (MAGENTA)
Causes: Scanner (writing) unit (LSU) polygon motor lock signal detection trouble (The lock signal is not detected for 10 sec after turning on the polygon motor.)
Remedy: Case 1 Trouble position/cause Scanner (writing) unit (LSU) trouble Remedy (Check) Scanner (writing) unit (LSU) operation check (SIM 61-1) (Repair) Replace the scanner (writing) unit (LSU). / Power Source-ON (After-work) Adjust ADJM7/ADJM9/ADJM10 Note Case 2 Trouble position/cause ICU MAIN PWB trouble Remedy (Check) (Repair) ICUMAIN PWB replacement / Power Source-ON (After-work) Adjust ADJM9/M10/M12/M13/M14/M15/M17. / Re-enter setup values and adjustment values. (Install the EEPROM of the defective ICU MAIN PWB to a new ICU MAIN PWB.)

Code: L6 13

Description: Scanner (writing) motor lock detection (YELLOW)
Causes: Scanner (writing) unit (LSU) polygon motor lock signal detection trouble (The lock signal is not detected for 10 sec after turning on the polygon motor.)
Remedy: Case 1 Trouble position/cause Scanner (writing) unit (LSU) trouble Remedy (Check) Scanner (writing) unit (LSU) operation check (SIM 61-1) (Repair) Replace the scanner (writing) unit (LSU). / Power Source-ON (After-work) Adjust ADJM7/ADJM9/ADJM10 Note Case 2 Trouble position/cause ICU MAIN PWB trouble Remedy (Check) (Repair) ICUMAIN PWB replacement / Power Source-ON (After-work) Adjust ADJM9/M10/M12/M13/M14/M15/M17. / Re-enter setup values and adjustment values. (Install the EEPROM of the defective ICU MAIN PWB to a new ICU MAIN PWB.)

Code: L8 1

Description: Power full wave signal (FWS) trouble
Causes: "The power full wave signal (FWS) is not detected. / AC power waveform distortion, noise"
Remedy: Case 1 Trouble position/cause Fusing oil collection pipe section short connector trouble Remedy (Check) Check the fusing oil collection pipe section short connector. (Repair) Replace the fusing oil collection pipe section short connector. / Power Source-ON (After-work) Note Case 2 Trouble position/cause PCU SUB PWB trouble Remedy (Check) Check the power full wave signal (FWS) circuit. (Repair) PCU SUB PWB replacement / Power Source-ON (After-work) Note Case 3 Trouble position/cause PCU MAIN PWB trouble Remedy (Check) Check the power full wave signal (FWS) circuit. (Repair) Replace the PCU MAIN PWB. / Power Source-ON (After-work) Re-enter setup values and adjustment values. (Install the EEPROM of the defective PCU MAIN PWB to a new PCU MAIN PWB.) Note Case 4 Trouble position/cause DC SUB power PWB trouble Remedy (Check) Check the power full wave signal (FWS) circuit. (Repair) DC SUB power PWB replacement / Power Source-ON

Code: L8 2

Description: Power full wave signal (FWS) width trouble
Causes: "The power full wave signal (FWS) is not detected. / AC power waveform distortion, noise (When the detection cycle is judged as 69Hz or more or 42.5Hz or less.)"
Remedy: Case 1 Trouble position/cause Fusing oil collection pipe section short connector trouble Remedy (Check) Check the fusing oil collection pipe section short connector. (Repair) Replace the fusing oil collection pipe section short connector. / Power Source-ON (After-work) Note Case 2 Trouble position/cause PCU SUB PWB trouble Remedy (Check) Check the power full wave signal (FWS) circuit. (Repair) PCU SUB PWB replacement / Power Source-ON (After-work) Note Case 3 Trouble position/cause PCU MAIN PWB trouble Remedy (Check) Check the power full wave signal (FWS) circuit. (Repair) Replace the PCU MAIN PWB. / Power Source-ON (After-work) Re-enter setup values and adjustment values. (Install the EEPROM of the defective PCU MAIN PWB to a new PCU MAIN PWB.) Note Case 4 Trouble position/cause PCU SUB PWB trouble Remedy (Check) Check the power full wave signal (FWS) circuit. (Repair) PCU SUB PWB replacement / Power Source-ON
Đăng ký nhận bản tin Đăng ký nhận bản tin Đăng ký nhận bản tin Đăng ký nhận bản tin
Đăng ký nhận bản tin
Nhận ưu đãi sớm nhất khi chương trình diễn ra

Đăng ký nhận bản tin

Việc cho phép sử dụng cookie sẽ giúp cải thiện trải nghiệm của bạn trên trang web này. Chính sách cookie