Thương hiệu phân phối chính hãng
Giỏ hàng

Mã lỗi Sharp MXM200DK — Trang 4/7

Code: F6-88

Description: FAX board communication trouble (Time out)
FAX board communication error.
Causes: There is no respond command from the FAX for 30sec or more.
Remedy: Check connection of the FAX board. Replace the FAX board. Reset the machine (Power OFF/ON).

Code: F6-97

Description: Combination error between the FAX unit and the main unit
Combination error between the FAX unit and the main unit
Causes: When this fax unit is installed to the machine that can not install this.
Remedy: Check the model name of the main unit

Code: F6-99

Description: Machine - FAX language error
Discrepancy of the destination of the machine and the FAX board.
Causes: The destination of the machine differs from that of the FAX board.
When installing to the machine that can install only AR-FX11.
Remedy: Change the destination setting with SIM26-6. Replace the FAX board with one which. conforms to the destination of the machine.

Code: F9-00

Description: MX-NB10 communication trouble
MX-NB10 print data reception error.
Causes: Print data cannot be received from the MX-NB10 for 3 min or more.
Remedy: Reset the machine (Power OFF/ON).

Code: H2-00

Description: Thermistor open
The thermistor is open. The fusing unit is not installed.
Causes: Thermistor abnormality.
Control PWB abnormality.
Fusing section connector disconnection.
The fusing unit is not installed.
Remedy: Check the harness and the connector between the thermistor and the PWB. Use SIM 14 to clear the self diagnostic display.

Code: H3-00

Description: Heat roller high temperature detection
The fusing temperature exceeds 240C°.
Causes: Thermistor abnormality.
Control PWB abnormality.
Fusing section connector disconnection.
Remedy: Use SIM 5-02 to check the heater lamp blinking operation. When the lamp blinks normally. Check the thermistor and its harness. Check the thermistor input circuit on the control PWB. When the lamp keeps ON. Check the power PWB and the lamp control circuit on the MCU PWB. Use SIM 14 to clear the self diagnostic display.

Code: H4-00

Description: Heat roller low temperature detection
When the fusing temperature is lower than 150C° after 55sec from the start of warming up.
When the warming up complete temperature is not reached in 30sec from reaching 150C°.
When the fusing temperature is lower than 100C° after 20sec from ready start.
When the fusing temperature is lower than 145C° when printing.
Causes: Thermistor abnormality.
Heater lamp abnormality.
Thermostat abnormality.
Control PWB abnormality.
Remedy: Use SIM 5-02 to check the heater lamp blinking operation. When the lamp blinks normally. Check the thermistor and its harness. Check the thermistor input circuit on the control PWB. When the lamp does not light up. Check for disconnection of the heater lamp and the thermostat. Check the interlock switch. Check the power PWB and the lamp control circuit on the MCU PWB. Use SIM 14 to clear the self diagnostic display.

Code: H5-01

Description: 5-time continuous detections of POUT not-reached jam
Paper not-reached jams are detected 5 times or more continuously by the paper exit sensor (POUT). The jam counter is backed up and used for jobs after turning on the power.
Causes: A fusing jam is not canceled completely. (A jam paper remains in the machine.)
Paper exit sensor trouble or harness connection trouble
Defective installation of the fusing unit.
Remedy: Check the fusing section jam (for winding, etc.). Check the POUT sensor harness. Check installation of the fusing unit. Use SIM14 to clear the self diag display.
Đăng ký nhận bản tin Đăng ký nhận bản tin Đăng ký nhận bản tin Đăng ký nhận bản tin
Đăng ký nhận bản tin
Nhận ưu đãi sớm nhất khi chương trình diễn ra

Đăng ký nhận bản tin

Việc cho phép sử dụng cookie sẽ giúp cải thiện trải nghiệm của bạn trên trang web này. Chính sách cookie