Thương hiệu phân phối chính hãng
Giỏ hàng

Mã lỗi Toshiba e-Studio 165 — Trang 5/6

Code: E33

Description: PFP lower drawer transport jam (Paper not reaching the registration sensor): The paper fed from the PFP lower drawer does not reach the registration sensor after has passed the PFP lower drawer feed sensor.
Remedy: Open the transfer cover. there paper front the registration sensor?
YES Remove the paper. Is the registration sensor working? (Perform the input check the test mode: 13-[04. SENSOR TEST]
NO 1) Check if the connector of the registration sensor is disconnected. 2) Check if the connector CN26 on the MAIN board is disconnected. 3) Check if the connector pins are disconnected and the harnesses are open circuited. 4) Check if the conductor pattern on the MAIN board is short circuited or open circuited. 5) Replace the registration sensor. 6) Replace the MAIN board
YES Are the PFU transport clutches (High speed/Low speed) working? (Perform the output check the test mode: 04-203, 205)
NO 1) Check if the connectors of the PFU transport clutches (High speed/ Low speed) are disconnected. 2) Check if the connector CN4 on the MAIN board is disconnected. 3) Check if the connector pins are disconnected and the harnesses are open circuited. 4) Check if the conductor pattern on the MAIN board is short circuited or open circuited. 5) Replace the PFU transport clutches (High speed/Low speed). 6) Replace the MAIN board
YES 1) Check the condition of the pickup roller of paper source, and replace it if it is worn out. 2) Check the transport roller. Replace it if it is worn out.

Code: E35

Description: PFP lower drawer transport jam (Paper not reaching the PFU feed sensor): The paper fed from the PFP lower drawer does not reach the PFU feed sensor after has passed the PFP lower drawer feed sensor.
Remedy: Open the side cover. there paper front the PFU feed sensor?
YES Remove the paper. Is the PFU feed sensor working? (Perform the input check the test mode: 13-[04. SENSOR TEST]
NO 1) Check if the connector of the PFU feed sensor is disconnected. 2) Check if the connector CN4 on the MAIN board is disconnected. 3) Check if the connector pins are disconnected and the harnesses are open circuited. 4) Check if the conductor pattern on the MAIN board is short circuited or open circuited. 5) Replace the PUF feed sensor. 6) Replace the MAIN board.
YES Are the PFU transport clutches (High speed/Low speed) working? (Perform the output check the test mode: 04-203, 205)
NO 1) Check if the connectors of the PFU transport clutches (High speed/ Low speed) are disconnected. 2) Check if the connector CN4 on the MAIN board is disconnected. 3) Check if the connector pins are disconnected and the harnesses are open circuited. 4) Check if the conductor pattern on the MAIN board is short circuited or open circuited. 5) Replace the PFU transport clutches (High speed/Low speed). 6) Replace the MAIN board
YES the PFP transport clutch working? (Perform the output check the test mode: 04-225)
NO 1) Check if the connector of the PFP transport clutch is disconnected. 2) Check if any of the connectors CN241, CN242 and CN244 on the PFP board is disconnected. 3) Check if the connector CN13 on the MAIN board is disconnected. 4) Check if the connector pins are disconnected and the harnesses are open circuited. 5) Check if the conductor patterns on the PFP board and MAIN board are short circuited or open circuited. 6) Replace the PFP transport clutch. 7) Replace the PFP board. 8) Replace the MAIN board.
YES 1) Check the condition of the feed roller, separation roller and pickup roller of each paper source, and replace them if they are worn out. 2) Check the transport roller. Replace it if it is worn out.

Code: E36

Description: PFP lower drawer transport jam (Paper not reaching the PFP upper drawer feed sensor): The paper fed from the PFP lower drawer does not reach the PFP upper drawer feed sensor after has passed the PFP lower drawer feed sensor.
Remedy: Open the PFP side cover. there any paper front the PFP upper drawer feed sensor?
YES Remove the paper. Is the PFP upper drawer feed sensor working? (Perform the input check the test mode: 13-[04. SENSOR TEST])
NO 1) Check if the connector of the PFP upper drawer feed sensor is disconnected. 2) Check if either of the connectors CN241 or CN243 on the PFP board is disconnected. 3) Check if the connector CN13 on the MAIN board is disconnected. 4) Check if the connector pins are disconnected and the harnesses are open circuited. 5) Check if the conductor patterns on the PFP board and MAIN board are short circuited or open circuited. 6) Replace the PFP upper drawer feed sensor. 7) Replace the PFP board. 8) Replace the MAIN board.
YES the PFP transport clutch working? (Perform the output check the test mode: 04-225)
NO 1) Check if the connector of the PFP transport clutch is disconnected. 2) Check if any of the connectors CN241, CN242 and CN244 on the PFP board is disconnected. 3) Check if the connector CN13 on the MAIN board is disconnected. 4) Check if the connector pins are disconnected and the harnesses are open circuited. 5) Check if the conductor patterns on the PFP board and MAIN board are short circuited or open circuited. 6) Replace the PFP transport clutch. 7) Replace the PFP board. 8) Replace the MAIN board.
YES 1) Check the condition of the feed roller, separation roller and pickup roller of each paper source, and replace them if they are worn out. 2) Check the PFP transport roller. Replace it if it is worn out.

Code: E40

Description: Transfer cover open jam: The transfer cover has opened during printing.
Remedy: the ADU cover open?
YES Remove paper there any, then close the cover. Is the voltage 24V being supplied from the power supply unit? (Perform the input check the test mode: 13-[04. SENSOR TEST])
NO 1) Check if the connector for 24 V power supply is disconnected. 2) Check if the connector CN23 on the MAIN board is disconnected. 3) Check if the connector pins are disconnected and the harnesses are open circuited. 4) Check if the conductor pattern on the MAIN board is short circuited or open circuited. 5) Replace the MAIN board.
YES Replace the MAIN board.

Code: E41

Description: Front cover open jam: The front cover has opened during printing.
Remedy: the front cover open?
YES Close the cover. Is the front cover opening/closing switch working? (Perform the input check the test mode: 13-[04. SENSOR TEST])
NO 1) Check if the connector of the front cover opening/closing switch is disconnected. 2) Check if the connector CN3 on the MAIN board is disconnected. 3) Check if the connector pins are disconnected and the harnesses are open circuited. 4) Check if the conductor pattern on the MAIN board is short circuited or open circuited. 5) Replace the front cover opening/closing switch. 6) Replace the MAIN board.
YES the voltage 24V being supplied from the power supply unit? (Perform the input check the test mode: 13-[04. SENSOR TEST])
NO 2) Check if the connector CN23 on the MAIN board is disconnected. 3) Check if the connector pins are disconnected and the harnesses are open circuited. 4) Check if the conductor pattern on the MAIN board is short circuited or open circuited. 5) Replace the MAIN board
YES Replace the MAIN board.

Code: E42

Description: PFP cover open jam: The PFP cover has opened during printing.
Remedy: Is the PFP side cover open?
YES Remove the paper there any, then close the cover. Is the PFP side cover opening/closing switch working? (Perform the input check the test mode: 13-[04. SENSORT TEST])
NO 1) Check if the connector of the PFP side cover opening/closing switch is disconnected. 2) Check if either of the connectors CN241 or CN243 on the PFP board is disconnected. 3) Check if the connector CN13 on the MAIN board is disconnected. 4) Check if the connector pins are disconnected and the harnesses are open circuited. 5) Check if the conductor patterns on the PFP board and MAIN board are short circuited or open circuited. 6) Replace the PFP side cover opening/closing switch. 7) Replace the PFP board. 8) Replace the MAIN board
YES Replace the PFP board. Replace the MAIN board.

Code: E44

Description: PFU cover open jam: The PFU cover has opened during printing.
Remedy: Is the PFU cover open?
YES Remove the paper there any, then close the cover. Is the PFU cover opening/closing switch working? (Perform the input check the test mode: 13-[04. SENSOR TEST])
NO 1) Check if the connector of the PFU cover opening/closing switch is disconnected. 2) Check if the connector CN4 on the MAIN board is disconnected. 3) Check if the connector pins are disconnected and the harnesses are open circuited. 4) Check if the conductor pattern on the MAIN board is short circuited or open circuited. 5) Replace the PFU cover opening/closing switch. 6) Replace the MAIN board.
YES Replace the MAIN board.

Code: E51

Description: Jam not reaching the ADU sensor: The paper does not reach the ADU sensor after is switchbacked the exit section.
Remedy: Open the ADU. there any paper front the ADU sensor?
YES Remove the paper. Is the ADU sensor working? (Perform the input check the test mode: 13-[04. SENSOR TEST])
NO 1) Check if either of the connectors CN251 on the ADU board is disconnected. 2) Check if the connector CN13 on the MAIN board is disconnected. 3) Check if the connector pins are disconnected and the harnesses are open circuited. 4) Check if the conductor patterns on the ADU board and MAIN board are short circuited or open circuited. 5) Replace the ADU board. 6) Replace the MAIN board.
YES Check the rollers the ADU. Replace them they are worn out.
Đăng ký nhận bản tin Đăng ký nhận bản tin Đăng ký nhận bản tin Đăng ký nhận bản tin
Đăng ký nhận bản tin
Nhận ưu đãi sớm nhất khi chương trình diễn ra

Đăng ký nhận bản tin

Việc cho phép sử dụng cookie sẽ giúp cải thiện trải nghiệm của bạn trên trang web này. Chính sách cookie