Thương hiệu phân phối chính hãng
Giỏ hàng

Mã lỗi Toshiba e-Studio 2007 — Trang 7/8

Code: E510

Description: Paper transport jam (ADU section) Jam not reaching the ADU transfer sensor: The paper does not reach the ADU transfer sensor after it is switchbacked in the exit section.
Causes: ADU transfer sensor MAIN board Exit motor ADU exit sensor Rollers in the ADU Exit roller
Remedy: 1 Open the right cover. Is there any paper in front of the ADU transfer sensor? Yes Remove the paper. No 2 2 Is the ADU transfer sensor working? (Perform the input check in the test mode: 03-[FAX]OFF/[1]/ [C]) Yes 3 No • Check if the connector of the ADU transfer sensor is disconnected. • Check if the connector CN17 on the MAIN board is disconnected. • Check if the connector pins are disconnected and the harnesses are open circuited. • Check if the conductor patterns on the MAIN board are short circuited or open circuited. • Replace the ADU transfer sensor. • Replace the MAIN board. 3 Is the exit motor (rotating in reverse) working? (Perform the output check in the test mode: 03-121/ 171) Yes 4 No • Check if the connector of the exit motor is disconnected. • Check if the connector pins are disconnected and the harnesses are open circuited. • Replace the exit motor. • Replace the MAIN board. 4 ADU • Check the rollers in the ADU and the exit roller of the equipment. Replace them if they are worn out.

Code: E550

Description: Paper remaining jam on the transport path: The paper is remaining on the transport path when printing is finished (caused by a multiple paper feeding).
Causes: Sensor. MAIN board
Remedy: 1 Open the cover of the unit/ area whose picture is blinking on the control panel. Is there any paper on the transport path? Yes Remove the paper. No 2 2 Is the sensor in the jamming area working? (Perform the input check in the test mode: refer to the following table) Yes 3 No • Check if the connector of the sensor is disconnected. • Check if any of the connectors on the MAIN board is disconnected. • Check if the connector pins are disconnected and the harnesses are open circuited. • Check if the conductor pattern on the MAIN board is short circuited or open circuited. • Replace the sensor. 3 MAIN board • Replace the MAIN board.
Registration area Right cover Registration sensor 03-[A]/[A] Exit area Right cover Exit sensor 03-[A]/[B] ADU Right cover ADU transfer sensor 03-[1]/[C] PFU PFU side cover PFU drawer feed sensor 03-[4]/[A] PFP PFP side cover PFP upper drawer feed sensor 03-[1]/[E] PFP upper lower feed sensor 03-[2]/[C]

Code: E552

Description: Paper remaining jam on the transport path (when the cover is closed)
Causes: Sensor in the jamming area. MAIN board
Remedy: 1 Jamming transport path Open the cover of the unit/area whose picture is flashing on the control panel and remove any paper on the transport path. 2 Sensor in the jamming area • Sensor check (Refer to the table below) • Harness check • Connector check 3 MAIN board • Harness check • Connector check • Board check Notes: If the jam is occurring in the PFU, check the board in each unit.
Registration area Right cover Registration sensor 03-[A]/[A] Exit area Right cover Exit sensor 03-[A]/[B] ADU Right cover ADU transfer sensor 03-[1]/[C] PFU PFU side cover PFU drawer feed sensor 03-[4]/[A] PFU PFU side cover PFU drawer feed sensor 03-[4]/[A] PFP PFP side cover PFP upper drawer feed sensor 03-[1]/[E] PFP upper lower feed sensor 03-[2]/[C]

Code: E714

Description: Feed signal reception jam: The feed signal is received even no original exists on the original feeding tray.
Causes: Original empty sensor RADF board
Remedy: Original empty sensor • Sensor check (Perform the input check: 03-[8]/[B]) • Lever check • Connector check • Harness check RADF board • Board check • Connector check (PA5) • Harness check

Code: E721

Description: Jam not reaching the read sensor: The original does not reach the read sensor after it has passed the registration sensor (when scanning obverse side) or the reverse sensor (when scanning reverse side).
Causes: Read sensor RADF board Transport roller-1 Transport roller-2
Remedy: Transport roller-1 / Transport roller-2 Clean the transport roller-1 and transport roller-2 if they are stained. Read sensor • Sensor check (Perform the input check: 03-[8]/[G]) • Connector check • Harness check RADF board • Board check • Connector check (PA4) • Harness check

Code: E725

Description: Stop jam at the read sensor: The trailing edge of the original does not pass the read sensor after its leading edge has reached this sensor.
Causes: Read sensor RADF board Transport roller-2
Remedy: 1 Transport roller-2 Clean the transport roller if it is stained. 2 Read sensor • Sensor check (Perform the input check: 03-[8]/[G]) • Connector check • Harness check 3 RADF board • Board check • Connector check (PA4) • Harness check

Code: E726

Description: Stop jam at the exit sensor: The trailing edge of the original does not pass the exit sensor after its leading edge has reached this sensor.
Causes: Original intermediate transport sensor RADF board Exit/reverse roller Replace it if it is worn out.
Remedy: Exit/reverse roller Clean the exit/reverse roller if it is stained. Original intermediate transport sensor • Sensor check (Perform the input check: 03-[8]/[E]) • Connector check • Harness check RADF board • Board check • Connector check (PA4) • Harness check

Code: EAD0

Description: Print end command time-out jam: Jam occurred because print operation did not finish normally due to communication error on main board
Causes: Main motor MAIN board
Remedy: 1 Is the main motor working? (Perform the output check in the test mode: 03-101/ 151) Yes 2 No • Replace the main motor. 2 Replacing the PC board Replace the MAIN board.
Đăng ký nhận bản tin Đăng ký nhận bản tin Đăng ký nhận bản tin Đăng ký nhận bản tin
Đăng ký nhận bản tin
Nhận ưu đãi sớm nhất khi chương trình diễn ra

Đăng ký nhận bản tin

Việc cho phép sử dụng cookie sẽ giúp cải thiện trải nghiệm của bạn trên trang web này. Chính sách cookie