Thương hiệu phân phối chính hãng
Giỏ hàng

Mã lỗi Toshiba e-Studio 2051c — Trang 7/33

Code: C911

Description: Toner cartridge IC chip access board abnormality (caused by factors other than C910)
Causes: Toner cartridge LGC board HRNS-LGC-TNRIC-140 CTIF board HRNS-TNRIC-140
Remedy: 1 Does non-genuine toner cartridge display appear when the front cover is opened and closed? Yes Use the genuine toner cartridge. 2 No 2 2 Toner cartridge • Check the phenomenon by removing the toner cartridges (Y, M, C and K) and reinserting them. • Check that the CTRG board of each cartridge (Y, M, C and K) is installed properly. 3 Contact point on the equipment side Check that the spring of the contact point for each color (Y, M, C and K) is not deformed. 4 Is the spring of the contact point returned when it is pushed lightly? Yes No • Check that the CTIF board is installed properly. • Board check 7 Notes: The spring of the contact point may be released if you push the toner cartridge all the way in when an abnormality occurs. 5 LGC board • Connector check (CN364) • Board check 6 HRNS-LGC-TNRIC-140 • Relay connector check (J556, J557, J558, J559) • Harness check 7 CTIF board for each color (Y, M, C and K) • Check that the board is installed properly. • Board check 8 HRNS-TNRIC-140 for each color (Y, M, C and K) • Connector check • Harness check

Code: C940

Description: Engine-CPU abnormality
Causes: LGC board
Remedy: Main power switch Turn OFF the main power switch, then back ON. Engine-CPU, FROM, and SRAM Check if the conductor pattern between the Engine-CPU, FROM, and SRAM is short circuited or open circuited. LGC board Board check

Code: C962

Description: LGC board ID abnormality
Causes: LGC board IMG board
Remedy: LGC board • Connector check (CN344, CN354) • Board check IMG board • Connector check (CN423, CN425) • Board check

Code: C970

Description: High-voltage transformer abnormality: Leakage of the main charger is detected.
Causes:
Remedy: Main charger Check if the main charger is installed securely. Spring of high-voltage supply contact point Check if the spring of high-voltage supply contact point is deformed. Needle electrode • Check if the needle electrode is broken or the main charger grid is deformed. • Check if any foreign matter is on the needle electrode or main charger grid.

Code: C9E0

Description: Connection error between SLG board and SYS board
Causes: SLG board IMG board SYS board
Remedy: SLG board • Connector check (CN12) • Board check IMG board • Connector check (CN421, CN422) • Board check SYS board • Connector check (CN135) • Board check

Code: CA00

Description: color registration abnormality
Causes:
Remedy: 1 <Color toner low density> Check the printing status. Is the color printing ratio 5% or more? Yes 2 No The color toner low density might be the cause. Turn the code 08-2692 "Prevention of color toner low density / ON/OFF setting" to ON, and then set number of sheets to be judged at the code 08- 2693 "Prevention of color toner low density/Judged number of sheets setting". 2 Open the front cover and take off the exit tray. (Refer to "4.1.2 Exit Tray".) 3 Take off toner cartridges (Y) and (M), and then close the front cover. 4 Perform color registration pattern / image quality control pattern.Is an image created on the transfer belt? Yes 8 No 5 5 Check if there is any abnormality on the hand grips and rods of the main charger cleaner. Correct if there is. 6 Check if the drum is rotated properly by turning the coupling of the developer unit. Correct the auger and the surrounding hardware if not. 7 Laser optical unit • Check the connectors and harnesses between the LGC board (CN343, CN355, and CN356) and the laser optical unit. • Check if there is any stain or scratch on the glass surface of the laser optical unit. Clean or correct if there is. 8 Check if there is any stain on the image quality sensor and Image position aligning sensors. 9 Check if the sensor shutter is working properly. 10 < Invalidating color registration control > • Turn the power ON while [0] and [8] are pressed simultaneously. • Key in “4546”, then press the [START] button. (08-4546: Position adjustment control / Mode setting) • Set the value to “0” (not performed automatically). • Turn the power OFF. 11 < Checking the abnormal status on color registration > • Turn the power ON while [0] and [5] are pressed simultaneously. • Key in “4720”, then press the [START] button. (05-4720: Displaying the cause of color registration detection error)

Code: CA10

Description: Polygonal motor abnormality: The polygonal motor is not rotating normally.
Causes: Laser optical unit LGC board
Remedy: 1 Is the polygonal motor rotating? Yes 3 No 2 2 Polygonal motor Connector check 3 LGC board • Connector check (CN343, J506) • Board check 4 Laser unit cooling fan • Check if the laser unit cooling fan is stopped. • Check if the suction area of the laser unit cooling fan is plugged up. 5 Units with high-voltage • Check if the units with high-voltage (developer unit, transfer belt unit, 2nd transfer roller unit) are securely grounded. • Check if the bias supply joints of the units with high-voltage are securely connected or they are not stained. 6 Plate in the paper transport system Check if the plate in the paper transport system is securely grounded. 7 Equipment Check if the equipment is grounded. 8 Laser unit cooling fan • Check if the laser unit cooling fan is stopped. • Check if the suction area of the laser unit cooling fan is plugged up. e-STUDIO4540C 1 Is the polygonal motor rotating? Yes 2 No 3 2 Is the printed image distorted? Yes 3 No 6 3 POL board • Connector check (connectors on the both edges of the HRNS-POLDRV- 382) • Board check 4 4 LGC board • Connector check (CN343, J506) • Board check 5 5 Laser unit cooling fan • Check if the laser unit cooling fan is stopped. • Check if the suction area of the laser unit cooling fan is plugged up. 6 LGC board Board check 7 Units with high-voltage • Check if the units with high-voltage (developer unit, transfer belt unit, 2nd transfer roller unit) are securely grounded. • Check if the bias supply joints of the units with high-voltage are securely connected or they are not stained. 8 Plate in the paper transport system Check if the plate in the paper transport system is securely grounded. 9 Equipment Check if the equipment is grounded. 10 Laser unit cooling fan • Check if the laser unit cooling fan is stopped. • Check if the suction area of the laser unit cooling fan is plugged up.

Code: CA20

Description: H-Sync detection error: H-Sync signal detection PC board cannot detect laser beams.
Causes: Power supply unit Laser optical unit LGC board
Remedy: 1 LGC board • Check the connectors and harnesses between CN356 and LDR board. • Check the connectors and harnesses between CN355 and SNS board. • Connector check (J503, J505) 2 Front cover ADU Close the front cover and ADU if it is open. 3 Is the pin CN405-4 on the power supply unit +5V? Yes 4 No 5 4 Is the pin CN361-4 on the LGC board +5V? Yes 6 No 5 5 Power supply unit Check the connectors and harnesses between the power supply unit and LGC board. 6 LGC board Board check 7 Units with high-voltage • Check if the units with high-voltage (developer unit, transfer belt unit, 2nd transfer roller unit) are securely grounded. • Check if the bias supply joints of the units with high-voltage are securely connected or they are not stained. 8 Plate in the paper transport system Check if the plate in the paper transport system is securely grounded. 9 Equipment Check if the equipment is grounded. 10 Laser unit cooling fan • Check if the laser unit cooling fan is stopped. • Check if the suction area of the laser unit cooling fan is plugged up.
Đăng ký nhận bản tin Đăng ký nhận bản tin Đăng ký nhận bản tin Đăng ký nhận bản tin
Đăng ký nhận bản tin
Nhận ưu đãi sớm nhất khi chương trình diễn ra

Đăng ký nhận bản tin

Việc cho phép sử dụng cookie sẽ giúp cải thiện trải nghiệm của bạn trên trang web này. Chính sách cookie